Will The Curt Pintle Hook Mounting Plate Fit In The Hitch Of A 2024 Chevy Silverado 3500

Question

Question:

Will the C48348 fin it a 2024 Silverado 3500? Just curious if the gusset will allow to fit in receiver?

asked by: Bill

0

Expert Reply:

The Curt Pintle Hook Mounting Plate for 2-1/2" Hitches # C48348 will fit in any 2-1/2" x 2-1/2" trailer hitch receiver tube opening so you shouldn't have an issue with your 2024 Chevy Silverado 3500.

expert reply by: Kevin C

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 10

Hey Kenny, welcome back! The reason for that note is because all of the new systems since 2025 use R32 refrigerant due to EPA regulations. Any 2024 and older systems use R410A and their parts are not compatible with the R32 units. It doesn't mean…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Hi Tharen! With the TorkLift StableLoad Suspension Upgrade for Upper Overload Springs #TLA7200 installed on your unloaded 2026 Chevy Silverado 3500 (congrats on the new truck!!!), it will make the ride harsher, unfortunately. Upper overload springs…

view full answer...

Will The Curt Pintle Hook Mounting Plate Fit In The Hitch Of A 2024 Chevy Silverado 3500

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching