Does Dexter Offer a Replacement Outer Cover/Case For The DX7.5L A-60 Brake Actuator # DX29FR?

Question

Question:

Do you sell a replacement cover or case for this trailer coupler/actuator? If so, what is the part number?

asked by: Barry J

0

Expert Reply:

While Dexter does offer a Replacement Inner Member # DX99FR for the Dexter DX7.5L A-60 Brake Actuator # DX29FR, the outer case is only available with the entire actuator. You will need to get a whole new actuator but be sure to save your current inner member if it is in good condition so you can use it should the new actuator become damaged internally over time.

expert reply by: Bud M

0

Answer 1

I took a look at the A-60 Surge Brake Actuator like the Dexter #DX56FR, and to remove the front pin you'll need to remove the locking ring from the front rolling pin on the passenger side, and push it out from the passenger side to the driver…

view full answer...

Answer 2

The Dexter DX7.5L A-60 Brake Actuator #DX56FR has a 2" ball coupler and is compatible with disc trailer brakes. While this actuator does come with an electric lockout that ties to the reverse light circuit to prevent pressure from getting to the…

view full answer...

Answer 3

Yep, you got it, the bolt hole dimensions are 3" x 2-1/2" for the Dexter DX7.5L A-60 Brake Actuator For Disc Brakes #DX29FR. This fits over a 3" x 4" tongue and the ball to opposite end length you stated does not matter, no.

view full answer...

Answer 4

The Dexter DX7.5L A-60 Brake Actuator w Electric Lockout part #DX29FR for disc brakes and part #DX27FR for drum brakes use 1/2" diameter mounting hardware. We have used both grade 5 and grade 8 bolts when doing installations of them but the…

view full answer...

Answer 5

The Trailer Coupler Lock #e98887 will work with a UFP A-60 coupler like your Dexter A-60 #DX56FR. The product picture for this lock shows it being used on an A-60.

view full answer...

Answer 6

There is not a rebuild kit so you would need to replace your UFP A-60/A-75 disc brake actuator, with the correct one depending on if you have a 3" x 5" or 3" x 4" straight tongue: - 3" x 5" Straight Tongue: Dexter DX7.5L…

view full answer...

Answer 7

The two wires on the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX29FR you purchased are for the reverse lockout solenoid. It does not matter which wire gets connected to what, but one wire…

view full answer...

Answer 8

Hey Bruce, you'd want to make sure the tongue of your trailer is 3 inch wide to verify for sure that the Dexter actuator part #DX29FR fits. This is also designed for 2 inch hitch balls and the brake type needs to be disc.

view full answer...

Answer 9

We do have replacement hydraulic actuators for your UFP A60 boat trailer actuator: If the actuator mounts on top of the trailer frame use part #DX89FR, but if it mounts inside of the trailer frame use part #DX29FR instead. These disc brake actuators…

view full answer...

Answer 10

Len, the banging that you're describing is absolutely a common symptom of a bad shock component, so all you need to fix it is to replace it with the Replacement Shock Absorber Spring Kit for Dexter Brake Actuators #TK71-758-00.

view full answer...

Answer 11

The Dexter DX7.5L A-60 Brake Actuator w Electric Lockout #DX29FR would work for you as it's for disc brake trailers and can fit a 3 inch wide trailer tongue like you have.

view full answer...

Answer 12

That's a really good question, and there is a difference between the 7,500 lb Dexter DX7.5L A-60 actuators for disc brakes; the differences are both in what they fit, as well as their length. - 14" Long & Top-Mounted For 3" Wide…

view full answer...

Does Dexter Offer a Replacement Outer Cover/Case For The DX7.5L A-60 Brake Actuator # DX29FR?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching