Replacement Bulbs for Optronics # ST16RB Taillight

Question

Question:

What are the correct replacement bulbs for the opt tonics to-16RK boat trailer taillights?

asked by: Mark

1

Helpful Expert Reply:

The Trailer Light Kit you referred to uses an # ST16RB and a # ST17RB taillight, which use a 1157 replacement bulb which we offer as part # DI79VR
.

expert reply by: Mike L

1

Answer 1

For the right side tail light assembly, use part #ST16RB. Part #ST17RB is the assembly for the drivers or left hand side. These will be an exact replacement for what you currently have. The ST17RS is the same light, sold individually. ST17RB is sold…

view full answer...

Answer 2

Virtually any three-wire tail-light assembly would work for you, since this is a boat trailer you will want to use a light assembly that is submersible. You will just need to wire the new tail lights in to your current wiring, mount the tail light…

view full answer...

Answer 3

Hi Randall; the Optronics Combination Trailer Tail Light #ST17RB you were looking at is my recommendation to replace your Wesbar lights. For the passenger side you need the #ST16RB. These measure 8-1/16" long x 2-7/8" tall x 2-13/16"…

view full answer...

Answer 4

Hey Kenneth, The clear portion at the bottom of the Optronics Combination Trailer Tail Light #ST17RB is for the license plate light. The housing for the #ST17RB is sealed to prevent water from getting in and the electrical components are encased in…

view full answer...

Answer 5

Yes, we have a right and left hand trailer tail light that you described. For the left hand side you would want a Over 80 inch, Rectangular Submersible Trailer Tail and License Light, 3 Wire, 8-Function, Left Hand, part #ST17RB. For the right hand…

view full answer...

Answer 6

I went out to the warehouse and pulled an Optronics Tail Light, #ST17RB. The mounting hardware is included with the light. The bolt heads actually fit into the slots on the back of the light and you tighten them on using the included nuts.

view full answer...

Answer 7

We do have an option for you, though the matching driver's side of the Aero Pro Trailer Tail Light - Submersible - Passenger Side ST66RPG has been discontinued and is no longer available. What I highly recommend instead is the Optronics Trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Replacement Bulbs for Optronics # ST16RB Taillight

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching