Correct Rhino-Rack Roof Rack for Factory Tracks 63 Inches Apart

Question

Question:

I bought a set of rhino rails from you for my 2023 Ford F150. The rails you sent me are 55” wide but the slots on my truck bed are 63” apart. Are they the wrong size rails?

asked by: Jim S

0

Expert Reply:

I took a look at your order and it was the Rhino-Rack Roof Rack for Factory Tracks - 54" Bars # Y02-480B-NT which is too short for the 63 inch spacing on your truck. For that spacing you will need the following:

- Rhino-Rack Roof Rack for Factory Tracks - 65" Long # Y02-500B-NT

expert reply by: Kyle S

0

Answer 1

Although it's never been tested yes, the Thule Tracker Fit Kits would fit in the track part #RTC16 as the Thule also uses track nuts that are 3/4 inches wide like the Yakima towers.

view full answer...

Answer 2

Yes, the 63" Rhino-Rack RTC-Style Roof Rack Tracks - Channel Mount part #RTC16 can be cut down to the size you need as long as you cut them perfectly straight to allow the end caps to go back on because at this time we do not carry them as a…

view full answer...

Answer 3

Looking at the 2019 Ram we installed these on I'm guessing the 71" bars are what you need but I would measure just to be sure. Run a tape measure across the bed of your 2024 Ram to see what the best size would be for your application. If the…

view full answer...

Answer 4

Yes, to keep the Rhino-Rack Vortex Crossbars #RRVA180B-RRRLT600 from interfering with the operating handle on your Retrax XR cover you just need the Roof Rack Leg Spacer Blocks #RRQMVA25. These will raise the crossbars 25 mm (0.98") more above…

view full answer...

Answer 5

The 71" Rhino-Rack Vortex Crossbars for Retrax XR Tonneau Covers item #RRVA180B-RRRLT600 are the correct set for your 2022 Ram 3500. These are made for full size trucks and fit in the rails of the Retrax PRO XR. These crossbars are exactly…

view full answer...

Answer 6

Hey Peter, There unfortunately are no type of extensions for the Rhino-Rack Vortex Crossbars for Retrax XR and Mountain Top EVO-M Tonneau Covers #RRVA180B-RRRLT600. There are just spacers for it so the crossbars sit up higher from the Retrax XR…

view full answer...

Answer 7

What I would do is go out to your truck and measure out 71 inches and 65 inches on a tape measure and compare that to the width of your bed. If you think the 71 inch looks better and would suit your needs then that's what you would want to go…

view full answer...

Answer 8

Everything you mentioned is compatible with one another. The RetraxONE XR Hard Tonneau Cover #RTX24YR is a fit for your 2020 Chevy Silverado 1500 with the 5-3/4 foot bed and has tracks that are compatible with the Rhino Rack Retrax XR crossbar set…

view full answer...

Answer 9

Thanks for the photo, and yes, the LockNLoad will indeed fit to Rhino-Rack Vortex aero crossbars like your Rhino-Rack Vortex Crossbars for Retrax XR #RRVA180B-RRRLT600. You'll just need adapters to mount the platform, and here are the part…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Correct Rhino-Rack Roof Rack for Factory Tracks 63 Inches Apart

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching