Is There A Straight Shank Available For The Jack-It 2 Bike Rack for A-Frame Trailers

Question

Question:

Where it connects to the base and rack are they 2” tube wanna put a straight tube up instead of the angle

asked by: Tom

0

Expert Reply:

Lippert offers a straight shank replacement for the Jack-It 2 Bike Rack for A-Frame Trailers # LC429756 with part # LC67HD. This shank is going to have the bikes sit a bit higher since it has an 8-1/4" spacing between the hitch pin holes.

expert reply by: Kevin C

0

LC67HD Hole Spacing
(click to enlarge)

Answer 1

The Jack-It Pro 2 Bike Rack for A-Frame Trailers #LGA47ZR we carry only comes with the angled stinger, but you can pick up the straight stinger separately as part #LC67HD on our site. This then allows you to have the bikes offset or directly above…

view full answer...

Answer 2

It is not a good idea to use weight distribution with a folding tongue due to the amount of force applied by the spring bars to the trailer. If you were to do it you would need to have a pole tongue adapter such as #RP58393 since the trailer does not…

view full answer...

Answer 3

Hey Durno, The Lets Go Aero Jack-It TS TwinSpin Bike Rack for 2 Bikes #LGA23VR comes with locks for both the bikes and the rack, but you are definitely more than welcome to add a cable lock to the mix as well for some extra peace of mind, and for…

view full answer...

Answer 4

There isn't a shorter angled shank for the Jack-It 2 Bike Rack for A-Frame Trailers #LC429756, but there is a straight shank #LC67HD that sits higher that might allow the bikes to sit above the bed of the truck so that they no longer come into…

view full answer...

Answer 5

Hey Sharlene, thanks for reaching out! I have a few options for you to look at, but ultimately there aren't any ball mounts that sit further out and have a receiver on top of them with enough clearance for your bike rack. The first option would…

view full answer...

Answer 6

Hi Cole, There are a couple options for air bags for your 2024 Ford F-150 4WD with the EcoBoost engine, it just depends on if your truck is equipped with Continuously Controlled Damping (CCD) or the optional Onboard Scales. I didn't see an option…

view full answer...

Answer 7

Hey Dustin, thanks for reaching out. I am not quite sure what you mean by sensor bars. Are you referring to the Firestone Automatic, Pneumatic Height-Control Valves #F2017? If so, we do offer an air bag kit/compressor system that can be used with…

view full answer...

Answer 8

Hello John, great question. We do have the Electric Jack w/ Footplate #EJ-3520-BBX which measures 20-1/2" from the bottom of the bracket to the top of the jack and is rated for 3,500 lbs. So, it sounds like this will be short enough to work with…

view full answer...

Answer 9

Hey Brian, There is not an adapter or any way to use the TopShelf for Yakima EXO SwingBase #Y94VR in a vertical 2 inch receiver. The TopShelf does require you to use the Yakima EXO SwingBase Swing Away Hitch Extender #Y34VR. If you're looking for…

view full answer...

Answer 10

Yes the Jack-It 2 Bike Rack for A-Frame Trailers part #LC429756 will work out well with your E Pro 20BHS. It is the best option for the front of your camper to haul bikes to your destination. I have a solution but unfortunately there are no 4 bike…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Is There A Straight Shank Available For The Jack-It 2 Bike Rack for A-Frame Trailers

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching