Will the 6 on 5-1/2 Kodiak 12" Rotor item # KR12S Replace a 12” UFP Brake Rotor?

Question

Question:

Will the Kodiak 12” Stainless steel, brake rotor, fit in place of a 12” UFP brake rotor. Stud size bolt pattern are the same.

asked by: Tom M

0

Expert Reply:

Yes, it will. If your 12” UFP brake rotor has 6 on 5-1/2 bolt pattern then the Kodiak 12" Rotor item # KR12S will work.

expert reply by: Jerred H

0

Answer 1

The Bronze Bushings - Qty. 4 #K71-291-00 will work well with the wet bolts #34007-187-00 which are 3-5/8 inches long. The usable length is 2-1/4 inches which will work well with the bronze bushings that are 1.74 inches long. The neverfail bushings…

view full answer...

Answer 2

The best thing you can do to help prevent rust on your #K2R526D rotor surface is to clean them before storing the trailer. It is likely you will still get a little surface rust which is a common occurrence and not something to be overly worried…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Will the 6 on 5-1/2 Kodiak 12" Rotor item # KR12S Replace a 12” UFP Brake Rotor?

Product Page this Question was Asked From

Continue Researching