Inner and Outer Diameters of Pipe Mount Piece for Bulldog Square Swivel Jack w/ Round Pipe Mount

Question

Question:

Hello Sir, Im replacing the trailer jacks and Id like to know the outter and inner diameters of the pipe mount on the jack side of a Bulldog trailer jack Item # BD190758. regards

asked by: Tom L

0

Expert Reply:

The jack-side pipe mounting piece from the Bulldog Square Swivel Jack w/ Round Pipe Mount # BD190758 has a 2" inner diameter and a 2-1/2" outer diameter.

expert reply by: Jon G

0

Answer 1

I pulled the Bulldog square swivel jack #BD190758 from our warehouse to provide the measurements you requested. The jack is 26-inches in overall length, not including the handle. The handle radius is 8-1/2 inches for your reference. If the foot base…

view full answer...

Answer 2

The Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15 inch Lift - 7,000 lbs, item #BD198250, has a male pipe on the jack and a female receiver that welds to the trailer. This female receiver has an inside diameter of just over 2-1/2 inches to fit…

view full answer...

Answer 3

The Bulldog Square Swivel Jack w/15 inch Lift-5,000 lbs Item #BD190758 is approximately 25-1/2 inches long from bottom of footplate to top of jack when retracted. Links to more information attached.

view full answer...

Answer 4

I have a solution for you, but the Bulldog Round, Pipe-Mount Swivel Jack - Sidewind - 15" Lift - 5,000 lbs #BD178203 is not compatible with the Fastway Flip Foot #FA88-00-4500 since the leg and inner tube are a single piece. Instead, you'd…

view full answer...

Answer 5

Bulldog is made by the same company as Fulton so for a similar swivel trailer jack the part #BD195356 would work really great. It has a capacity of 3,000 lbs, swivels, and is a pipe mount so it would use same mount as what you have.

view full answer...

Answer 6

You would need a spacer of some type to allow the mounting brackets of the 55" Lock Side-Door Bar Lock Assembly #3057-55 to sit flush with the door so that it could close and latch. Otherwise the latch wouldn't get around the door.

view full answer...

Answer 7

Bracket height is the height of the jack from the center of the mounting bracket to the bottom of the jack when retracted and extended. In this case this jack #BD195356 is 15-1/8" Retracted and 30-1/8" Extended. From the top of the jack to…

view full answer...

Answer 8

Hey Kelly, so clearance as we define it, is going to be the distance from the mounting bracket to the top of the jack tube excluding the handle. Both of the extended and retracted measurements are going to be taken from the bottom of the footplate to…

view full answer...

Answer 9

The distance from the center of the pipe mount to the top of the Square Pipe Mount Swivel Jack w Footplate #TJDP-7000-B measures 10-1/4 inches.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Inner and Outer Diameters of Pipe Mount Piece for Bulldog Square Swivel Jack w/ Round Pipe Mount

Featured Help Information

Miscellaneous Media

Continue Researching