Can I Use My Existing Brackets to Replace the Furrion Over the Range RV Convection Microwave?

Question

Question:

We have this model FMCM15-SS in our 2019 Forest River Georgetown. Can we just use the existing brackets already on the wall for the original one when replacing with the new one, since it is same model number?

asked by: KC

0

Expert Reply:

Thanks for the pictures! Yes you can use your existing brackets to mount the Furrion Over the Range RV Convection Microwave item # FMCM15SS since you are just replacing the same model.

expert reply by: Jerred H

0

FMCM15-SS
(click to enlarge)

Answer 1

Yes we do! To replace your Furrion #FMCM15SS I recommend the High Pointe Over the Range RV Convection Microwave #HP94ZR. This unit measures 29-15/16" wide x 15-11/16" tall x 15" deep overall which is virtually identical to the Furrion…

view full answer...

Answer 2

There is indeed a built-in fuse on the Furrion Over the Range RV Convection Microwave part #FMCM15SS, it's located at the upper right hand corner on the back of the unit. Therefore, the unit would need to be removed in order to access the fuse.…

view full answer...

Answer 3

Hello Trent, thanks for reaching out. Does your RV happen to have a tow-rated bumper? If so, a great option for carrying/securing your generator is the 24x60 etrailer Enclosed Cargo Carrier for RV Bumper #e34VV. This attaches to a 4" or…

view full answer...

Answer 4

Hey Mike, we do have the Furrion Over the Range RV Convection Microwave #FMCM15SS if you're interested in keeping the same microwave. This is the exact same thing you have right now so it'll for sure fit in the existing cutout. If you want a…

view full answer...

Answer 5

I recommend the Furrion Over the Range RV Convection Microwave #FMCM15SS you were looking at as it is a top of the line Microwave Convection Oven that will look great installed in your 2004 Gulfstream Sun Voyager. I was able to find the dimensions of…

view full answer...

Answer 6

Yes. The mounting plate/bracket which holds the bottom of the unit to the wall is included with the Furrion Over-The-Range Convection Microwave #FMCM15SS . I have attached a picture to show what it looks like and where it is located on the…

view full answer...

Answer 7

The trim kit #FMSM09SSTK for this microwave #FMSN09BL is assembled before it is put on the microwave. To install you take the fully assembled trim, line it up and apply pressure until it snaps into place. Take a small flathead screwdriver and slide…

view full answer...

Answer 8

There are a couple of different trim kits from Furrion but it sounds like you have the Kit #FMSM09SSTK which presses onto the brackets that attach to the microwave. This trim pulls off the front to gain access to the screws which hold the microwave…

view full answer...

Answer 9

Hi Teagan, The Furrion Over the Range RV Convection Microwave #FMCM15SS has three mounting holes in the top of the unit as well as a metal bracket on the back at the bottom that you'd remove and screw to the wall. The bracket has multiple holes…

view full answer...

Answer 10

The best replacement option we offer for a Dometic Over the Range Microwave DOTR12CB is the Furrion Over the Range RV Convection Microwave part #FMCM15SS. This microwave is considerably larger than the one it's replacing at 29-15/16" wide x…

view full answer...

Answer 11

To remove the Trim Kit for Furrion Standard Microwave #FMSM09BLTK for the Furrion Standard RV Microwave #FMSN09BL, you can simply take a flat blade screw driver, or a flat tool and slide it underneath the trim and pry away from the trim, slowly…

view full answer...

Answer 12

If you remove the block off panel on the top of the Furrion Microwave part #FMCM15SS it will vent through that hole instead of forcing air to recirculate back into the RV.

view full answer...

Can I Use My Existing Brackets to Replace the Furrion Over the Range RV Convection Microwave?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching