Does the Black Armour Heavy-Duty Custom Truck Bed Mat Come in Two Pieces?

Question

Question:

frod f350 super duty 8 foot bed. is this mat in 2 parts??

asked by: Zachery B

0

Expert Reply:

Yes it is. The Black Armour Heavy-Duty Custom Truck Bed Mat item # BA67AR does come in two parts. This mat is confirmed to fit the 8' bed length of the 2022 Ford F-250.

We do have a one piece option for a custom fit rubber bed liner for your truck. It is the DeeZee item # DZ87012. This one is slightly thinner at 3/8" over the 1/2" for the Black Armour.

expert reply by: Jerred H

0

Answer 1

Hey Travis, welcome back! Yes the DeeZee bed mat part #DZ28GJ that you referenced can install over a factory spray in bed liner. Are you trying to keep the spray in bed liner as nice as possible and thats why you want a mat?

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 11

Hello Joe, Thank you for reaching out! The Power Mountain Tallboy Off-Road Bottle Jack - 11-5/16" to 27-1/16" Lift - 12 Tons #PM94FR does have the capacity you’d need, but since your fifth wheel’s frame sits about 25" off the ground,…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Does the Black Armour Heavy-Duty Custom Truck Bed Mat Come in Two Pieces?

Product Page this Question was Asked From

Continue Researching