Will A Rhino Rack Platform Work With The Rails On The RSI Smartcap On A Jeep Gladiator

Question

Question:

Will this product, Rhino-Rack Pioneer Platform Rack - 52" Long x 54" WideWide, fit on an RSI Smartcap EVOa for Jeep Gladiator?

asked by: Bradley M

0

Expert Reply:

I was able to look up a bit of info on there RSI smartcaps, although we do not carry them here. It appears the tracks they put on top are designed to be universal. In that case I recommend the Pioneer platform for tracks # RR98QX. This will include everything you need to mount the 52" x 54" platform to your RSI cap.

expert reply by: Jesse M

0

Answer 1

Since we don't currently offer the RSI Smartcap I don't have any real technical info on it, but since you say they have t-slots you could use a system like the Rhino-Rack Roof Rack for Thule and Yakima Tracks #Y01-140B-NT. This rack attaches…

view full answer...

Answer 2

Yes, your RSI SmartCap load bars are compatible with, and will allow you to mount the Hullavator, which is the following part number: - Thule Hullavator Pro Kayak Carrier and Lift Assist #TH898 I have added a link below to a video review for you to…

view full answer...

Answer 3

We do not have custom channel nuts. Unfortunately, our best option for you would be to remove the tracks on your RSI Smart Cap and just install the corresponding length Rhino-Rack tracks. I have included a weblink to our Rhino-Rack track options…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Sure, I can help with that. I can see why the fitment notes are confusing. For a 2012 Toyota Tundra with the factory tow package and factory 7 way connector, you'll want a brake controller that plugs into the factory brake controller port under…

view full answer...

Answer 10

Hey Dale, thanks for reaching out. For your 2010 Toyota Tundra with the factory tow package, a proportional controller is definitely the way to go for smooth braking on a 2-axle trailer, and a really clean option is the Redarc Tow-Pro Liberty…

view full answer...

Answer 11

Hey Connor, since your 2007 Toyota Tundra comes with a factory 7-way the correct kit to install the Redarc Tow Pro Liberty would be the part #RED82CR which comes with the correct harness that plugs in under the dash of your truck. What are you…

view full answer...

Answer 12

Hello Barry, Since you already have a weight distribution (WD) hitch and are only experiencing a little rear sag, I recommend going with SumoSprings. I typically only suggest Timbrens for those who are towing heavy loads regularly, as they can create…

view full answer...

Will A Rhino Rack Platform Work With The Rails On The RSI Smartcap On A Jeep Gladiator

Continue Researching