Parts Needed to Add Brakes to 2004 Fleetwood Pecos Pop-Up Camper
Updated 07/05/2023 | Published 07/01/2023 >
Products Featured in This Question
Question:
I want to add an electric braking sytem to my Fleetwood 2004 pecos tent trailer. What do I need? I also have to add a controller to my vehicle for the braking system
asked by: Sean C
Expert Reply:
Adding brakes to your 2004 Fleetwood Pecos Pop-Up Camper will require hub and drum assemblies, brake assemblies, 7-way wiring, and a breakaway kit. However, the first thing you need to do is check and see if you have a brake flange on the axle.
If you do not have a brake flange, you will either need to weld one on or replace the axle. Either way you will need to identify the axle and capacity to do this. The best way is to check the axle tag. If you can send me or the axle manufacturer a picture of the axle tag that information can be used to identify the axle.
If you do have a brake flange, you will still need the axle capacity to choose the right brakes. you will also need to know what bearings it uses to find the correct hub and drum assembly. For example, if you had a standard 3,500 lb axle with a 4-bolt brake flange pattern you could use the following:
-Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles # AKHD-545-35-EZ-K
-Electric Trailer Brake Kit - Self-Adjusting # AKEBRK-35-SA
-7-Way Wiring: Hopkins 7-Way Molded Trailer Wire Connector # HM20048 (If you want a junction box use # 3375601101)
-Breakaway Kit: Hopkins Engager Push-To-Test Trailer Breakaway Kit # 20400
If this doesn't match your axle capacity, or you don't have a brake flange, please let me know and I will help you find the correct parts once you identify what axle you have on the camper. One way or another, the 7-way and breakaway kit will work for you.
For a brake controller, I recommend the Redarc Tow-Pro Liberty # RED24FR. The main unit mounts out of sight with only the control knob visible in the cab of your vehicle. This means it won't take up space and it has a nice clean look. The knob controls the brake power and also acts as the manual override. You will also need # RED69FR for installation. It is possible a custom wiring harness is available, but I would need to know the year, make, and model of your vehicle to check.
I have attached some review and installation videos below for your reference.
Product Page this Question was Asked From
etrailer Rubber Hitch Cover for 2" Trailer Hitches - Qty 1
- Hitch Covers
- Misc Covers
- Plain
- Rubber
- Fits 2 Inch Hitch
- Standard
- Square
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Does Curt Hitch for 2026 Toyota Corolla Cross Also Fit Hybrid Models
- Q&A: Recommended Hitch for a 2026 Toyota Corolla Cross and How to Install It
- Q&A: Will The etrailer Hitch e83ZR Fit A 2026 Subaru Forester Wilderness?
- Q&A: Recommended Flat Towing Parts for a 2026 Ford Maverick Lariat
- Q&A: Stealth Hitch that Fits 2024 Ford Mustang Mach-E
- Q&A: Why Does the etrailer Trailer Hitch part # e72AR Have a Higher Towing Capacity than the Vehicle?
- Q&A: Best Replacement For Older Dometic Duo Therm 57915.531 Ducted Single Zone AC System With Furnace
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Article: How to Measure for Trailer Hitch Drop
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: 5 Reasons to Convert Your RV Lights to LEDs Today
- Article: Can I Put Wallpaper in My RV?




