Why Can't Trailer Axles Actually be Flipped

Question

Question:

I have axle with 4 inch drop spins facing up with underslung leaf springs with the arch/ camber facing up like a rainbow ?? or a frown ??. I have about 3 to 4 inches clearance at U bolts and axle now which is no where near enough. I can achieve 4 ish inches with over under kit . Question, can I flip axle with 4 inch spins facing down and achieve same thing ? Or would camber be wrong and cause damage ? Hoping you can help ? Thank you very much

asked by: Ainsley R

1

Helpful Expert Reply:

You have to use an over under kit to gain the additional height you are after. Due to the bow in the axle that you mentioned you can't just rotate the axles 180 degrees as the camber would be way off. I don't know what diameter axle your trailer has but if it's 3 inch you'd want the over under kit part # K71-385-00 or if it's 2-3/8 inch we have the # K71-384-00.

expert reply by: Jameson C

1

Answer 1

The over under conversion kits like #K71-385-00 only work on round axles. What you can do depends on why you need to raise the trailer. If you need more clearance under the trailer you can replace the leaf spring hangers with longer ones. You have to…

view full answer...

Answer 2

Moving a trailer axle from being overslung to underslung really isn't a big ordeal. It's basically just welding on a new spring seat on the other side of the axle and then using the hardware upside down. We sell kits for this. The diameter of…

view full answer...

Answer 3

Based on the picture you submitted that shows a square axle welded to a mount which is then welded to a leaf spring you would need to have someone qualified use a cutting torch to remove the mount from the spring so that you could then use a u-bolt…

view full answer...

Answer 4

I'm pretty confident you have a 1-3/4" round tube axle on your Carry On 5x8 trailer. Having a 2" axle is uncommon and is typically only found with square tube axles, which you don't have on your trailer. While there isn't a…

view full answer...

Answer 5

Since you do not want to use an over/under kit on your axle, the best way to raise the trailer would be to use longer hangers for the leaf springs. You may be able to use a hanger like part #E4139. This hanger is designed for double-eye springs and…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Why Can't Trailer Axles Actually be Flipped

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching