Replacement Axle for Lippert 3,500 lb Axle 95 inch Hub Face to Hub Face 80 inch Spring Seat

Question

Question:

I need a replacement axle for our trailer. Here’s the lippert number off the axle tag lc135-db-95-80-nosp-us-l-545-7242-18pt I can’t find that exact one so I’m curious if someone can find a similar replacement

asked by: Will P

0

Expert Reply:

Based on the numbers I can see in your axle part number what you have is a 3,500 lb trailer axle with a distance of 95 inches from hub face to hub face and 80 inches from spring seat center to spring seat center. We have an axle that matches that perfectly with the Dexter part # 7359765.

expert reply by: Jameson C

0

Answer 1

First things first; you can determine the specs on your current axle by checking for a sticker or plate attached to the axle itself (you'll usually find it close to the center of the axle). But with that being said, in the event that you…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hey Greg, yes the Aluminum Hi-Spec Series 04 Star Mag Trailer Wheel #AM20258 that you referenced would work with a Load Range E tire ST175/80R13 like you mentioned.

view full answer...

Answer 11

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Axle for Lippert 3,500 lb Axle 95 inch Hub Face to Hub Face 80 inch Spring Seat

Product Page this Question was Asked From

Continue Researching