Replacement Hub for Dexter 8-256 that Has 5 on 5 inch Bolt Pattern

Question

Question:

I have 2 Dexter 8-256 hubs that I took off to inspect and re-pack bearings. I cannot seem to get the inner seal off of the first one I took of the spindle, so Im guessing a replacement is warranted lol. I have 5 on 5inch bolt pattern, but there are no identifying marks on the outer bearings. With that info, do you think the AKIHUB-550-35-K assembly would work for me? Trailer is a 2004 Miky 12x6foot utility trailer. Thanks for your help in advance

asked by: Sam D

1

Helpful Expert Reply:

For a replacement hub for your Dexter 8-256 that has a 5 on 5 inch bolt pattern you would want the part # 84550BX which comes with replacement bearings and a seal.

expert reply by: Jameson C

1

Answer 1

The Dexter "8-256" is a hub assembly that uses an L68149 inner bearing and a L44649 outer bearing. This hub assembly was offered in a few different bolt patterns therefore you would need to confirm your bolt pattern using the attached help…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 5

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Replacement Hub for Dexter 8-256 that Has 5 on 5 inch Bolt Pattern

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching