Replacement Fender for 2004 Yacht Boat Trailer

Question

Question:

Have a 2004 Yacht boat trailer. Need a right fender. The tire size is 14inch. Do you have anything that will fit?

asked by: Terry

0

Expert Reply:

I am not totally sure what would be a perfect replacement match but if you are looking for a replacement plastic fender that would fit your 2004 Yacht boat we have the CE Smith part # CE19504 for black or for white part # PF11X35W.

expert reply by: Jameson C

0

Answer 1

Yes, the Fulton Single Axle Trailer Fenders #F008594-2 that you referenced will work on an EZ loader trailer like yours. These were designed for 14 inch wheels like what you have and we've had customers come back and tell us they worked well on…

view full answer...

Answer 2

I do have an option for you but we do not carry Shoreland'r branded boat trailer parts. However, I was able to do some research on your boat trailer using the VIN you provided and came back with the Fulton Single Axle Trailer Fenders part…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Replacement Fender for 2004 Yacht Boat Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching