Recommended Longer Threaded Hitch Bolt for a Hollywood Racks Bike Carrier on a 2020 Toyota Tacoma

Question

Question:

I’m looking for this exact product, but a little bit longer. My Toyota Tacoma 2020, for some reason I need a longer screw.

asked by: Chris

0

Expert Reply:

Sounds like what you'd need is the Replacement Threaded Hitch Bolt for Hollywood Racks Sport Rider and Traveler Bike Carriers # HRHPN-13 which is 5/8" longer than the Replacement Threaded Hitch Bolt for SportRack Bike Racks and Cargo Carriers # 05002400000 you currently have.

expert reply by: Bryce D

0

Answer 1

The section under the head of the hitch pin bolt part #HRHPN-13 that you referenced measures 4 inches.

view full answer...

Answer 2

Hey Michael, The Threaded Hitch Pin for Thule Snug Tite Hitch Lock #TH62RE is 4-1/2" long overall, with the threaded portion being 1-3/8" and the rest being 3-1/8". It is longer than most, which are often 3-1/2" or so, and I know…

view full answer...

Answer 3

The Replacement Threaded Hitch Bolt for Hollywood Racks Sport Rider and Traveler Bike Carriers #HRHPN-13 is a 1/2" - 13 bolt meaning it has a 1/2" diameter and coarse thread pitch.

view full answer...

Answer 4

It looks like you have an older Thule T2 Hitch Mount Bike Rack and the correct replacement hitch bolt/pin for this is the Thule Snug Tite Hitch Lock and Anti-Rattle Device part #THSTL2 for locking or Threaded Hitch Pin for Thule part #TH62RE for…

view full answer...

Answer 5

The hitch pin bolt you'll need for a Thule bike carrier/rack is the Replacement Threaded Pin for Thule part #853-5917. It is indeed an M12x1.75 bolt which is roughly 4" long. I can't confirm compatibility of thread pitch for the…

view full answer...

Answer 6

The correct replacement hitch pin for your Thule Trailblazer Bike Rack 998 is the Thule Replacement Hitch Pin Assembly for Bike Carriers part 853-5019-02. The problem is that this pin is no longer made as the rack is very old and there isn't a…

view full answer...

Answer 7

The other option is to use an adapter such as #HT02. This will allow you to use the 1-1/4 inch bike rack shank in a 2 inch receiver.

view full answer...

Answer 8

All Thule bike racks use the same threaded hitch pin so you can use the Replacement Threaded Pin for Thule Snug Tite Hitch Lock and Anti-Rattle Device #853-5917. This is just the threaded bolt, and you'll need to use the flat washer, lock washer…

view full answer...

Answer 9

Yes the threads are 12mm x 1.75. The threaded portion is 1 3/8" long and the non threaded length is right at 3".

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Recommended Longer Threaded Hitch Bolt for a Hollywood Racks Bike Carrier on a 2020 Toyota Tacoma

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching