Torque Spec on Bolts for Demco Channel Tongue Trailer Coupler - eZ-Latch - Zinc - 2" Ball - Bolt On

Question

Question:

What is the torque used to tighten the nuts on the 1/2inch class 8 bolts for this coupler?

asked by: Perry

1

Helpful Expert Reply:

In order to install the Demco Channel Tongue Trailer Coupler part # 12564, you'll need to obtain three 1/2" Grade 8 Hex Bolts about 3-1/2" - 3-3/4" long with nuts from a local hardware store. The recommended torque for a bolt this size/grade is 80 ft. lbs.

expert reply by: Conner L

1

Answer 1

No, I am sorry. The only way to purchase the slide pads is with the Replacement Roller/Pin/Pad Kit for Dexter Brake Actuators item #TK71-759-00. How old is your actuator?

view full answer...

Answer 2

The straight tongue couplers like the Dutton-Lainson 3-Inch Trailer Coupler, part #DL13897 are available for trailer tongues with either a 2-inch, 2-1/2-inch, or 3-inch channel. I would recommend for you to measure the trailer channel at a point…

view full answer...

Answer 3

It sounds like you're looking for a brake actuator that fits a 2" ball for your 2017 Trailstar. The dimensions don't have to match up, although it is nice if they do. The important thing is to know the capacity you need and whether this…

view full answer...

Answer 4

Yes, the Demco Channel Tongue Trailer Coupler #12564 that you referenced does accept a 2-inch hitch ball and mounts to a 3-inch-wide trailer tongue. It's mounting hole spacing is indeed 3-inches and it offers a 10,000-lb weight capacity.…

view full answer...

Answer 5

I may have a solution for you but I'm not aware of a bolt on safety chain bracket or clevis that can be used. However you can simply take a safety chain set (or your existing chains) like the 42" Long Safety Chain with 3/8" Clevis Hook…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Hello James, thanks for reaching out. Both the kits you mentioned, the Hydrastar #HYD22FR and #HYD42FR are complete conversion kits for standard 3,500 lb axles. The difference is the calipers included with each kit. The #HYD22FR has stainless steel…

view full answer...

Torque Spec on Bolts for Demco Channel Tongue Trailer Coupler - eZ-Latch - Zinc - 2" Ball - Bolt On

Product Page this Question was Asked From

Continue Researching