Were Cams of Reese Dual Cam III Upgraded from Previous Version

Question

Question:

Is the cam component of this new hitch better than the old style cam unit? I have a 20 year old dual cam that is due for replacement for peace of mind and to assure nothing breaks. Thank you for your insight.

asked by: Bob W

0

Expert Reply:

Yes, the cam of the Reese Dual Cam III part # RP65FR has been upgraded from models that were made 20 years ago. The brackets have also been upgraded and made to be a lot easier to install as well.

expert reply by: Jameson C

0

Answer 1

Hey Rick, I looked up your Alliance RK234 and based on what it weighs the weight distribution and sway control system I recommend is the Strait Line II part #RP65FR which is the correct weight rating and also has the best sway control that works to…

view full answer...

Answer 2

Each weight distribution hitch has a tongue weight capacity range where it's most effective and can help evenly distribute the weight of the trailer. If the fully loaded weight of your trailer is 8,400lbs and you keep increasing the rating of the…

view full answer...

Answer 3

That is a great question. Both of those are great weight distribution hitches. Between the two, I prefer the Reese Dual Cam II over the Strait Line. The Dual Cam uses an L-bracket to attach to the frame, instead of a chain and lift bracket.…

view full answer...

Answer 4

Hello Chris, The equalizer is a great choice! When it comes to sway control it is top notch! When choosing the right weight distribution tongue weight is most important. I would go with the Equal-i-zer Weight Distribution System w/ 4-Point Sway…

view full answer...

Answer 5

Hello again, Phil. Out of those two options I definitely recommend the Reese Dual Cam II #RP65FR with the no-drill frame brackets. In my experience, any WD system that uses no-drill L-brackets that bolt to the frame is going to be much easier to set…

view full answer...

Answer 6

Hello Michael, thanks for reaching out. Regrettably, we do not offer high enough rated Reese round bars for your new camper. Also, like you said, the new Reese Dual Cam 2 is only goes up to a 1,200 lb tongue weight rating so this is not a good option…

view full answer...

Answer 7

Hey Randall, The brackets could just be swapped out but unfortunately aren't being sold separately at the moment. You could try reaching out to Reese directly to see if they could sell you just the brackets, otherwise you'd have to purchase…

view full answer...

Answer 8

I recommend using the Reese Weight Distribution Shank item #RP69FR. This fits a 2" hitch receiver. It has a maximum drop of 4" and a maximum rise of 9".It is 13-3/4" long. These shank will work perfectly with the Reese Dual Cam II…

view full answer...

Answer 9

Absolutely, the most effective weight distribution system we carry in regards to sway control is the Equal-i-zer Weight Distribution System. These are considered to be one of the best on the market. They have a 4-point sway control system whereas…

view full answer...

Answer 10

We do sell replacement trunnion bars for Reese weight distribution systems that have the curved ends which are designed for use with the dual cam systems. The Reese Replacement Trunnion Spring Bar, 1200 lbs, item #RP66009, is most likely what you…

view full answer...

Answer 11

If your current weight distribution system is less than 3 years old, then you will be able to use the Replacement Trunnion Spring Bar, #RP66009. If it is the old style system, the bars will not fit in the head. The head you would need is #RP58167.…

view full answer...

Answer 12

Based on your photo, it appears you have the dual cam system of the Reese Strait-Line. I researched your trailer to find a GVWR of 5895. Based on this, we can make some calculated assumptions on the tongue weight. The tongue weight of a trailer is…

view full answer...

Were Cams of Reese Dual Cam III Upgraded from Previous Version

Continue Researching