Reason for Metal Ring Inside the Stainless Steel Seal Ring on Spindle Grease Seal Set

Question

Question:

In the photos of this product it shows a snap ring or circlip that resides in the sleeve. Ive yet to find a clarification on the snap ring / circlips purpose. The instructions are very vague. I found a set of instructions that states to torque the spindle nut to 20 foot pounds then back it off. Im assuming the torqueing compresses the seal ring on to create a tight fit. Does this sound correct? However I fear torqueing to 20 foot pounds will put stress on the tapered roller bearings. Please advise if you can.

asked by: RICHARD P

0

Expert Reply:

According to Bearing Buddy, the purpose of the metal ring inside the stainless steel seal ring on the # BB60005 is to add additional support. Because the seal ring is so thin in this kit, they added a support ring that goes in the back side of the seal ring so it doesn’t collapse. The support ring is required. Regarding the instructions for the Spindle Grease Seal Set, it calls for 20 inch pounds of torque, not foot pounds.

expert reply by: Robin H

0

Answer 1

I recommend using the CE Smith Trailer Idler Hub Assembly #CE13515 for your Calkins boat trailer. These have the 5 on 4-1/2" bolt pattern and is prepacked and greased for your spindle. You can add the Bearing Buddy Bearing Protectors #BB1980A-SS…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Reason for Metal Ring Inside the Stainless Steel Seal Ring on Spindle Grease Seal Set

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching