Is it Normal to Have Residual Magnetism on an Electric Brake Magnet When No Power is Applied
Updated 12/05/2013 | Published 12/03/2013 >
Products Featured in This Question
Question:
Ive got a hot wheel problem due to brakes dragging on one wheel. The bearings are ok, and brake adjustment is ok. With no controller connection and battery on trailer disconnected, if I hold a screwdriver up to the magnet it will stick ... not super hard like on a speaker magnet, but enough to be noticeable. Is this normal?
asked by: Greg G
Expert Reply:
The magnet on an electric trailer brake assembly, such as # 23-27 from Dexter, is an electro-magnet (not a permanent magnet) that should exhibit magnetic attraction only when 12-volt power is applied to it. Even after extended use there should not be residual magnetism, certainly not enough that the magnet would hold the weight of a screwdriver.
It sounds like there must be some 12-volt power reaching the brake assembly. This would cause the always-engaged brake pads to heat up the assembly. I suggest you fully disconnect your trailer 7-way from the tow vehicle, and also one at a time completely remove your trailer batteries (if you have both a breakaway battery and an auxiliary power battery for the trailer). If the brake loses magnetism after removing one of the batteries you will know which one is leaking voltage to the brake circuit.
Carefully inspect the brake circuit wiring all the way from the trailer 7-way to the subject brake assembly; look for any cracks or worn spots in the brake wire insulation.
You can test the brake with a multimeter like part # PT89ZR. You can also test the magnet itself. Please refer to the linked article for step-by-step testing instructions.
Product Page this Question was Asked From
Dexter Electric Trailer Brake Assembly - 10" - Right Hand - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- RH
- 3500 lbs
- Brake Assembly
- Manual Adjust
- 10 x 2-1/4 Inch Drum
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: spindle nut
- Q&A: Repair Kit for etrailer Ram Jack # TJD-8000S
- Search Results: kit only trailer breakaway kit
- Search Results: trailer breakaway kit accessories and parts
- Search Results: demco 2" coupler
- Search Results: e track motorcycle
- Shop: Spindle Nut Kit for EZ Lube Axles
- Shop: Replacement Nut Retainer for 6-191 Jam Nut
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Replacement Sidewind Handle Assembly for etrailer and Ram Square, Direct Weld Jacks - 7,000 lbs
- Shop: CargoSmart Motorcycle Wheel Chock for E Track or X Track Systems - 7" Wide Tires
- Shop: Replacement Plug-In Remote for Bulldog Powersport Series UTV Winch - 12' Long
- Search Results: off road tire
- Shop: Premium Trailer Breakaway Kit w/ Safety Cable, Charger, LED Tester, and 5 Ah Battery - Side Load
- Search Results: electric brake magnets
- Shop: Trailer Wiring
- Shop: Gooseneck Hitch
- Q&A: Should a Trailer Brake Magnet Make Contact with a Drum Even With No Brakes Applied
- Q&A: What is Actual Way to Auto Adjust Self Adjusting Trailer Brake Assemblies
- Q&A: Troubleshooting Single Self-Adjusting Brake Assembly Repeatedly Over-Adjusting
- Q&A: How to Loosen Self-Adjusting Brakes
- Q&A: Replacement Electric Brake Magnet Retaining Clip for Dexter 8,000 lb Axle
- Q&A: Do Trailer Brake Magnets Touch Brake Drums All the Time
- Article: Trailer Wiring Diagrams
- Article: Testing Trailer Brake Magnets for Proper Function
- Video: Complete Breakdown of the Dexter Trailer Hub and Drum Assembly for 8,000-lb E-Z Lube Axles
- Video: Breaking Down the Replacement Magnet Kit for 10" Electric Trailer Brake Assemblies


