Replacement Electric Brake Magnet Retaining Clip for Dexter 8,000 lb Axle

Question

Question:

Do you sell magnet keepers to keep magnet on 8000 lb. Dexter axel brakes?

asked by: Rich

0

Expert Reply:

If you just want the magnet clips, you will use the Replacement Magnet Clips for Electric Brake Assemblies (Qty 4) # BP19005. If you need a replacement magnet, spring, and clip then I recommend the Replacement Magnet Kit for Dexter 12-1/4" Electric Brake Assembly # BP01-301.

expert reply by: Jason S

0

Answer 1

In regards to the Dexter Electric Brake Kit part #23-450-451 which uses the Replacement Magnet Kit for Dexter 12-1/4" Electric Brake Assembly part #BP01-301, the magnet is held onto the arm with a retaining clip included with the magnet. If you…

view full answer...

Answer 2

The magnet clips #BP19005 should not be making contact with the drum while the brakes engage, so I do not think that is the problem. What I think is going on is it's just not seating all the way. These can get a little squished or deformed…

view full answer...

Answer 3

Hey Jared, the brake spoon part #W80630 that you referenced would work fine as a brake adjuster for a 4 inch diameter trailer axle. This would be long enough to reach in and grab the star wheel.

view full answer...

Answer 4

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 5

In order to properly adjust the Dexter electric brake assemblies on your travel trailer, you will first need to raise the trailer and check that the wheel and drum rotate freely. Remove the adjusting hole cover from the slot on the bottom of the…

view full answer...

Answer 6

I spoke to my contact at Kodiak and they informed me that a socket should not be used when removing or installing the grease cap like part #KPCAP as this would likely cause damage to the polycarbonate material used in it's construction. If the…

view full answer...

Answer 7

The #BP19-001 retaining clips are designed to fit the Dexter 7-inch brake magnets. Our contact at Dexter said the BP19-001 will work on both the 7-inch round and the 10-inch oval magnets. The replacement magnet clip, part #BP19005 will fit 10, 12,…

view full answer...

Answer 8

The #W80630 brake adjustment tool we offer is two sided. One side has a 90 degree bend in it that makes accessing the brake adjuster on a drop spindle much easier. The #W80630 tool will work just fine for you.

view full answer...

Answer 9

When pulling the hubs off of a trailer and repacking the bearings you will inevitably unseat your brake shoes. Using the Brake Adjustment Spoon for Drum Brakes part #W80630 will allow you to make a slight adjustment to the brakes to tighten them up a…

view full answer...

Answer 10

Trailer spindle and bearing tolerances are pretty tight, usually down to a thousandth of an inch. Use of emery cloth on a spindle to remove scoring damage might remove enough material to affect the fit of the replacement bearing. You can be off the…

view full answer...

Answer 11

For a Dexter 8,000 lbs axle you will need the following parts: Inner Bearing item #25580 Outer Bearing item #02475 Grease Seal item #GS-2125DL (2.125") Grease Seal item #GS-2250DL (2.250") We do not sell these parts in a kit. You will need…

view full answer...

Answer 12

The seals #9103309 and #GS-2250DL have the same inner and outer diameters (2.250" ID and 3.376" OD) but they are used for different applications. Use the seal #9103309 if you have an oil bath setup but you'll want to use the seal…

view full answer...

Replacement Electric Brake Magnet Retaining Clip for Dexter 8,000 lb Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching