Replacement Shroud for Coleman Mach 3 on 1977 GMC Motorhome

Question

Question:

Hi, Im in search of a replacement shroud for a Coleman Mach 3 air conditioner. Im trying to match the pointy shape of the original cover. Why, you ask? This is on a 77 GMC front drive motorhome. The stock shroud matched the pointy shape of the motorhome. All the replacement shrouds Ive seen so far just wouldnt look right, at least my OCD says so. Thanks

asked by: Jeff M

0

Expert Reply:

The MaxxAir Replacement RV Air Conditioner Cover # MA8335A5261 will replace your Coleman Mach 3 shroud. Although it may not be as pointy as the original, the contours from the side profile aren't far off from the front of your 1977 GMC motorhome.

expert reply by: Robin H

0

MaxxAir Replacement RV Air Conditioner Cover.
(click to enlarge)

Answer 1

Hi Glenn, I was able to pull a few specs from your Dexter axle number, it looks like it is a 3.5K EZ-lube axle with 5 on 4 1/2 bolt pattern and a 2 3/8" diameter axle tube. I wasn't able to determine the hub face or spring center measurement…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Replacement Shroud for Coleman Mach 3 on 1977 GMC Motorhome

Featured Help Information

Miscellaneous Media

Continue Researching