Replacement LP Gas Detector for a CCI 7770.2 / Pre Tell 22 Detector

Question

Question:

Hello, I am looking for a replacement LP Gas Leak Detector for a CCI 7770.2 / Pre Tell 22

asked by: Andrew

0

Expert Reply:

We do have some LP gas detectors available, but none would be a direct replacement for your CCI 7770.2 / Pre Tell 22.

From what I could find on your CCI 7770.2 / Pre Tell 22, it has dimensions of 6.25" wide x 3.9" tall.

The RV Propane Gas Detector # RS44FR (black) and # RS64FR (white) measure 4-1/4" long x 2-5/8" tall but have two different bracket sizes to fit what you need.

Large bracket
- 7-1/4" long x 3-3/8" tall

Small bracket
- 5-3/4" long x 4-1/4" tall

expert reply by: Scott S

0

Jack F.

3/31/2024

it is actually 3 inches wide by 7 inches tall. The recessed part is 2.5 wide x 6 Tall. Any suggestion for a replacement that will fit the opening?

Reply

Answer 1

We know that the Fulton Fender part #F008583 that you referenced will easily fit on a Shoreland'r trailer that has tandem axles but it is not a direct bolt-on application. Some small modifications will need to be made. Check out the review I…

view full answer...

Answer 2

Really the only way to test your camera system is with known good components. While we do have a Replacement Monitor #VO34FR for your current Voyager AOM711 I would need to know what all camera components you also have. It might make more sense to…

view full answer...

Answer 3

You can replace your Voyager AOM-711 monitor with the Voyager RV LCD Observation Monitor #VO34FR. The monitor will work with any standard voyager camera. For a replacement camera I recommend the Voyager Rear Camera #VCMS17B. You mentioned you are…

view full answer...

Answer 4

The Replacement Screen Door Latch for Right Swinging RV Entry Doors #LC27UD you were looking at could be installed in place of your current latch, but would require modification to both the screen door and door threshold to line up with the plunger.…

view full answer...

Answer 5

What a lot of people do to mount a winch like the Superwinch Tiger Shark Series #SW1595200 to the floor of a trailer is use a hitch mount like the part #C31010 and then fabricate a hitch opening to the floor of the trailer like the #E-11 welded to…

view full answer...

Answer 6

Your brake lights and turn signals for each side are on one circuit. The left side turn signal and brake light is generally the yellow wire going into your trailer connector. The first thing to do is check the fuses on your tow vehicle. Next, inspect…

view full answer...

Answer 7

It sounds like there is constant power on the electric brake output pin in the trailer connector on your new Silverado. The first step I would take is to test the truck. Using a circuit tester with an incandescent bulb, like part #PTW2993, test the…

view full answer...

Answer 8

The EB01-140 and EB01-145 are Redneck Trailer Supply part numbers for a Dexter 12-1/4 x 3-3/8 7-bolt brake assemblies for a 9-10K axle. The proper replacements are available as part #23-450-451, which includes the left and right self adjusting brake…

view full answer...

Answer 9

The Gorilla-Lift Utility Trailer Tailgate Lift Assist part #GL1 is designed for tailgates no more than 300 lbs. There is not an option to upgrade the weight capacity nor is there a lift assist for a heavier tailgate. This would be he limit for a…

view full answer...

Answer 10

Hey George, sorry to hear about your previous experience with your leaf spring setup. I've been stranded on the side of the road because of a trailer malfunction as well and it definitely isn't a pleasant experience so I understand where…

view full answer...

Answer 11

In terms of choosing a Lippert Solid Step, you'll use the width of the finished door at it's narrowest. Round that number up to the next full inch, which in your case would be 28 inches. In that case, you'll want the adjustable model…

view full answer...

Answer 12

I recommend using the RV Propane Gas Detector - 12 Volt - 2 Wire - Black #RS44FR and using the larger 7-1/4" long x 3-3/8" wide bracket for the installation as that should be a little larger than your current model 7770.2 gas detector.

view full answer...

Replacement LP Gas Detector for a CCI 7770.2 / Pre Tell 22 Detector

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching