Chain Extension Kit For A Hensley Hitch

Question

Question:

Will the chain extension kit work with a Hensley hitch

asked by: Randy B

1

Helpful Expert Reply:

Yes, The Wiring and Safety Chain Extension Kit # PR34QR will work with your Hensley hitch per the manufacturer.

This kit will help you if your chains and cables do not extend 24 inches past the end of the hitch box. The working load of the chains is 15,800 pounds.

The 7-way extension that is included in this kit is 18 inches long.

I attached a review video link below.

expert reply by: Noah E

1

Answer 1

There is indeed a safety chain kit that is designed to be used with the ProPride 3P Weight Distribution Hitch w/ Sway Control for 2-1/2" Receivers #PR47QR. The correct part for this hitch is the Wiring and Safety Chain Extension Kit for ProPride…

view full answer...

Answer 2

Your thinking is 100% correct here. RV black water drains will be a standard 3" size, which is the internal diameter of the pipes, so the Valterra Waste Valve for RV Black Water Tank - Twist On - 3" Bayonet Hooks to 3" Lug #T58 will…

view full answer...

Answer 3

Personally I feel the SumoSprings Solo Custom Helper Springs #SSR-127-54 are a better option for more users on a 2024 Ford F-250 than the Timbren #TFR250SDJ. The SumoSprings are more more progressive and will provide a better ride quality when…

view full answer...

Answer 4

We do indeed have the exact bearing kit you need for your Lippert 5,100 lb axle with the part #BK3-300.

view full answer...

Answer 5

For a Dexter EZ Lube Spindle 5,200 lb capacity part #8-201-9UC3-EZ the bearings needed are #25580 and #15123. We have a bearing kit that has these as well plus the races and a new seal #BK3-110.

view full answer...

Answer 6

Thanks for the pictures of the axle information! Based on the information you provided your axle uses the following components: Inner bearing #25580 Inner race #25520 Outer bearing #LM67048 Outer race #LM67010 Grease Seal #GS-2250DL All of these…

view full answer...

Answer 7

I was unable to find any information with the numbers on your axle, unfortunately. However, you can contact the manufacturer of the trailer and they should be able to tell you exactly which inner and outer bearings you have. If for some reason they…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Chain Extension Kit For A Hensley Hitch

Featured Help Information

Miscellaneous Media

Continue Researching