Owners Manual for the Draw-Tite Activator Brake Controller # 5504

Question

Question:

I bought my Hyundai 2009 Santa Fe used. There is no manual for the Draw-Tite Activator 5504 brake controller. How can I get one. This one is not the same as I had on a previous vehicle.

asked by: Kent M

1

Helpful Expert Reply:

I attached a link that has the installation instructions and owners manual for the Draw-Tite Activator Brake Controller # 5504 that you referenced.

expert reply by: Jameson C

1

Answer 1

The Longview Custom Towing Mirrors #LVT-2600 are a confirmed fit for your 2001 Ford F-250 all models. These towing mirrors are designed to seamlessly fit the contours of your factory side-view mirrors. Plus, they won't scratch or mark your…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Our only custom fit trailer hitch receivers we have for your 2000 Ford Excursion are the Curt Class IV #C14011 and Torklift Class V #TLF1006. The Curt has one 2" receiver while the Torklift has two 2" receivers. We do have a Curt Class 5…

view full answer...

Answer 10

Hello Kyle. I am very sorry but we do not have a Class V hitch for the 2003 Ford Excursion. We do however have a Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2" #C14011 which is a custom fit to your Excursion. This hitch will line up…

view full answer...

Answer 11

Hey John, yes the brake controller wiring that comes with the 7-way kit part #22112 that you referenced will work with the Tekonsha Voyager brake controller part #TK26BR as it uses the same connector. Do you have the Voyager already?

view full answer...

Answer 12

Good afternoon James, yes the Stillwell jacks are made in the great United States of America! (see flag below). In regard to how they compare to other brands, they are going to be similar to the Dexter jacks we carry. The dexter will be just a little…

view full answer...

Owners Manual for the Draw-Tite Activator Brake Controller # 5504

Featured Help Information

Miscellaneous Media

Continue Researching