Replacement Brake Shoes for Brakes Used With Dexter 8-283 Hub and Drum Assembly

Question

Question:

Brake shoes dexter drum 8-283

asked by: Lawrence C

0

Expert Reply:

The correct replacement brakes for brake shoes that fit your 8-283 hub and drum assembly are the # bp04-065. We also have the # K71-362-00 if you need replacement springs as well.

expert reply by: Robin H

0

Paz

10/21/2024

Would like Dexter 8-283 10”x1 1/2” wheel bearing and seal numbers, and price, please? Also pads for same. Price for the hub and break assembly, should I replace all Instead. Thank you

Reply

Robin H.

10/21/2024

@Paz the 8-283 hub is obsolete so we can provide the bearings and seals but there is no direct replacement that will fit that spindle anymore. If you want new hubs you're looking at getting a new axle. For the inner bearing you need # LM67048 and race # LM67010. The outer bearing is # L44649 and race # L44610. The seal is # 10-42.

Reply

Paz R.

10/21/2024

@RobinH Thank you for your response. I will just order left and right set for one axel; brake shoes, bearings, and seals. You have been very helpful. I will go place order now. Paz

Reply

Paz

10/21/2024

@RobinH Sorry, I just noticed I gave you the wrong hub/drum number. It is not Dexter 8-238, it is 8-283. Can you please confirm the seal, bearing numbers, and brake shoes? Is the 8-283 still available? Thanks, I need to order ASAP. Paz

Reply

See All (5) Replies to Paz ∨

Answer 1

The Dexter 10K electric brakes #23-439 (right side) and #23-438 (left side) will have to be manually adjusted using the adjustment wheel below the magnet. To adjust the brakes you will use a small screwdriver or similar tool to turn the adjustment…

view full answer...

Answer 2

The Dexter 8-283 is an obsolete 2800lb 10 x 1-1/2 inch hub like you measured which the replacement shoes/linings part #BP04-065 that you mentioned are a correct fit for. For just the springs you'd want the part #K71-362-00. It's recommended…

view full answer...

Answer 3

For the inner bearing you need #LM67048 and race #LM67010. The outer bearing is #L44649 and race #L44610. The seal is #10-42.

view full answer...

Answer 4

Your Dexter 8-283 brake drum will use a #10-42 grease seal. If you are looking to replace all the races, bearings and seals you will want the following components per hub. Inner Bearing #LM67048 Inner Race #LM67010 Outer Bearing #L44649 Outer Race…

view full answer...

Answer 5

Sounds like you're needing the 10" x 1-1/2" Electric Brake Shoe/Lining (One Wheel) #bp04-065. These brake shoes will work with braking assemblies that are 10" x 1-1/2". So, for all four wheels you'd need to order 4 of…

view full answer...

Answer 6

Like you said, 10 x 1-1/2 inch brakes are hard to find. We currently do not offer any in that size. But the shoes, #bp04-065, are a fit for Dexter 10 x 1-1/2 inch brakes. The issue is that the axles associated with the Dexter 10 x 1-1/2 inch brakes…

view full answer...

Answer 7

It sounds like you want the replacement brake shoes for drum brakes and based on your description the 10" x 1-1/2" Electric Brake Shoe/Lining (One Wheel) #bp04-065 will work. I recommend also replacing the springs #K71-362-00 at the same…

view full answer...

Answer 8

The 10" x 1-1/2" Electric Brake Shoe/Lining #bp04-065 that you referenced can be used on both the right and the left had side brake assemblies normally seen on Dexter 2.8K axle.

view full answer...

Answer 9

Are there any visible signs of wear on the magnets like exposed windings then that would indicate they need replacing. Magnets can go bad without showing visible signs of wear though. To see how to troubleshoot them check out the help article I…

view full answer...

Answer 10

You will want the Replacement Brake Spring Set for Dexter 10" x 1-1/2" Electric Trailer Brake Assembly #K71-362-00. Then you will want the Replacement Trailer Brake Magnet Kit for 7" Brake Assemblies #BP01-068 due to the thinner hubs…

view full answer...

Answer 11

There is a slot for the adjuster spring at the bottom of the 10 inch by 1-1/2 inch Electric Brake Shoe Lining, #bp04-065. We do not carry a magnet clip for round magnets, but you can get the Trailer Brake Magnet Kit, #BP01-068, which will come with a…

view full answer...

Answer 12

For your Dexter 10x1-1/2 inch brakes the old magnet style was a round magnet, #BP01-068.

view full answer...

Replacement Brake Shoes for Brakes Used With Dexter 8-283 Hub and Drum Assembly

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching