Replacement Breakaway Kit For The Titan A-75 Actuator

Question

Question:

Good morning. Wondering if you carry a breakaway cable repair kit for an A 75 acuator. I see you have one for an A 60.Thank you!

asked by: Brian

0

Expert Reply:

We sure do!

What you're looking for is the:

-Replacement Emergency Breakaway Cable Kit for Dexter Axle A-75 and A-84 Brake Actuators # DX76XR.

This kit includes the breakaway cable, cable attachment plate, breakaway cable clip, pushrod release bracket, & the pushrod release bracket spring.

expert reply by: Bryce D

0

Answer 1

Thanks for the photos! Your coupler has pretty generic markings, but from what I can see if looks like you need one of the following parts: - Breakaway Cable for Model 60 Actuators #T4623800 - Breakaway Cable for Model A-75 and A-84 Actuators #DX76XR…

view full answer...

Answer 2

Hello Mike, For your A-60 surge brake actuator like the #DX56FR, you’ll want the Emergency Breakaway Cable Repair Kit for Dexter A-60 Brake Actuators #DX64XR to replace the cable. For the cover, the correct part is the Replacement Black Plastic…

view full answer...

Answer 3

Hi Gary; I'm sorry we don't have a video installing the #DX64XR at this time but I did go pull the installation manual out of the box for you. You need to remove the inner member and then route the cable as seen in the instructions. Dexter…

view full answer...

Answer 4

Hey Jay, thanks for all of the info and your picture. Based on seeing that the correct replacement inner member is the part #DX78CR.

view full answer...

Answer 5

The Replacement Shock Absorber Spring Kit #TK71-758-00 is the correct shock for your UFP Surge Brake Actuator. The picture you included does not specify if it is for a disc or drum brake set, so I have found both for you to choose from. Disc Brake…

view full answer...

Answer 6

This does happen every now and then, but you will need the Dexter Replacement Emergency Breakaway Cable Kit #DX64XR. This is specifically for the A-60 actuators, which the #DX56FR is. With that said, on the bottom or underneath side of the inner…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Breakaway Kit For The Titan A-75 Actuator

Product Page this Question was Asked From

Continue Researching