AC, Heat, and TV Mount Needed for Haulmark Race Trailer

Question

Question:

I bought 34` HaulmardK Edge Pro Race trailer. Its wired for A/C and Heat, what should I install. Running 9,500 watt generator. Also need a locking bracket for flat panel TV to lock TV while on road. Thank you

asked by: Eric A

0

Expert Reply:

If your trailer is set up for AC and heat then it sounds like an Atwood Air Command 15,000 BTU unit is what you're looking for. This comes in white as part # AT15028-22 or black as part # AT15033-22 and comes with a heat pump, thermostat, and ceiling vent. I have attached a review video for you to check out.

We also have a variety of TV mounts that I'm linking for you to check out. These install on your trailer in different ways and they fit different VESA mounting patterns so that's what you're mainly going to be looking at for a TV mount. The VESA mounting pattern are the holes in the back of your TV. You should be able to find the VESA pattern on the TV, in the manual, online, or even by measuring from the center of one hole to the centers of it's neighbors.

If you still need help with a TV mount just let me know what your VESA pattern is and I can help you out from there.

expert reply by: Jon G

0

Answer 1

Charles, it looks like the Predator 5000 generator you have is a bit a too big so it's not going to work with the MORryde RV Generator Slide Out Tray #MR89RR. You'd need to use a bigger tray like the MORryde RV Cargo Sliding Tray #MR37FR…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

AC, Heat, and TV Mount Needed for Haulmark Race Trailer

Featured Help Information

Miscellaneous Media

Continue Researching