Where to Install a Valterra Check Valve for RV Fresh Water Systems on a RV Water Heater

Question

Question:

Should the check valve be installed in both the cold inlet and the hot outlet of my water heater?

asked by: John H

0

Expert Reply:

You should only need the Valterra Check Valve for RV Fresh Water Systems # P23415LFVP at the cold inlet of your water heater. Typically you will have a total of three fresh water check valves; one at the cold inlet to the water heater, one at the city water inlet and one located at the outlet of the water pump.

expert reply by: Scott S

0

Answer 1

The Dexstar Steel Mini Mod Trailer Wheel - 16" x 6" Rim - 8 on 6-1/2 - Black #AM20761B have a maximum air pressure rating of 110 psi and a weight capacity of 3750-lbs.

view full answer...

Answer 2

The trailer tire manufacturers we work with all have recommended the information you have seen given in our online answers. The max PSI from most manufacturers the listed capacity at the highest load capacity rating of the ST tire. There are charts…

view full answer...

Answer 3

The Dometic model B59516 is showing up as a Brisk II 15K BTU unit so the only thing you'll need to check is what style connector your current unit has. If you remove the cover for the air distribution box inside the trailer you should see the…

view full answer...

Answer 4

The best option we have for you is to use the Valterra Check Valve part #P23415LFVP and then go to a local hardware store to look for a 1/2" to 5/8" adapter as we do not carry a check valve with both 1/2" MPT and 5/8" MPT…

view full answer...

Answer 5

Antifreeze leaking into the water heater could be remotely caused by a bad check valve, however, this would all depend on the location of the check valve. Generally speaking, there are only 2 check valves installed in the plumbing system for an RV.…

view full answer...

Answer 6

We do have some check valves available from Valterra and Camco, both of which are big in the RV plumbing industry and have great reputations. The 2 most popular check valves that we have are parts #P23415LFVP, which has 1/2" MPT x MPT fittings,…

view full answer...

Answer 7

The water leaking is normal its your overflow which means that your fresh tank is now full. If you install a valve on the overflow then it needs to be open when filling and when using or else the tank could explode. It could also be that your check…

view full answer...

Answer 8

The Valterra 1/2" check valve #P23415LFVP fresh water backflow preventer has an arrow stamped between the threading and the nut. It can be difficult to see, if you don't look closely. You should install the backflow preventer with the arrow…

view full answer...

Answer 9

Hello Dan, thanks for reaching out. You asked a good question so I went out to our warehouse and got my hands on the B&B RV Fresh Water Fill Diverter Valve and Plate Assembly #BM35RR. The threaded fittings are not bonded together, and I was…

view full answer...

Answer 10

Fresh water check valves are typically 1/2" NPT fittings, but I wouldn't know if you'd need a female or male connector without actually taking your city water inlet apart. If you remove your city water inlet from the wall of the trailer…

view full answer...

Answer 11

Brass fittings like the #P23415LFVP can be difficult to remove. Especially if there was thread locker or thread tape used. It's hard to say how much force you'd need but you might try heating up the fitting to release any thread locker.

view full answer...

Answer 12

Check valves can fail due to ice in the winter or debris in warmer months, or simple wear at any time. I think if it were me I would try to warm the check valve with a heat source like a heat gun, being careful not to melt the plastic around it. At…

view full answer...