Would Weight Distribution Hitch Need to be Adjusted When Adding Timbrens to 2021 Toyota Tundra

Question

Question:

Hello. I have a 2021 toyota tundra S5 4x4. I pull a single axle Lance travel trailer and I use a Curtis TruTrack weight distribution hitch when towing the trailer. Would I have to readjust the weight distribution hitch if I added the Timbren springs to the suspension? Thanks.

asked by: Mark H

1

Helpful Expert Reply:

Really good question, and you need to readjust your weight distribution system when installing Timbrens on your 2021 Toyota Tundra; the correct fit for those are the following:

- Timbren Rear Suspension Enhancement System # TTORTUN4

You'll need to readjust your hitch because the # TTORTUN4 will engage and help level your '21 Tundra when you have a trailer hooked up. Just the Timbrens alone though won't get you completely level or sway control, so using them with the TruTrack is really the best of both worlds.

expert reply by: Kyle S

1

Answer 1

Yes, this is normal. The Timbrens will engage first when you hook up the trailer and the weight distribution hitch will then work with the remaining sag. Just make sure you're not overloading your truck's tongue weight capacity and the weight…

view full answer...

Answer 2

For your electric jack, there are only three possible explanations for your jack not working with a charged battery. Either power is not getting to your motor, your motor is bad, or your ground connection isn't working properly. To test power,…

view full answer...

Answer 3

The fastest powered a-frame jack we offer is the Phoenix Jack part #UF38-944055 that you referenced which can travel 10 inches in just 47 seconds. Depending on where you would mount the battery would determine if you'd need a battery box.

view full answer...

Answer 4

You linked to the Valterra EZ Valve Electric Waste Valve for RV Black Water Tank, #E40-8 a 3" Hub to 3" Spigot. The difference between a hub connection and a spigot connection is that the hub is the female end and has a lip on the inside…

view full answer...

Answer 5

Plumbing parts are interchangeable on RV's just as long as the fittings are the correct size. I couldn't find that exact part number but I believe I have found the Valterra equivalent. If the Bristol valve you are talking about uses the…

view full answer...

Answer 6

The Valterra RV Sewer Spigot with Flange - 3" #T1006 will be compatible with LaSalle Bristol Valves. This has the standard mounting holes 3-3/4 inches apart on center. Then you will simply use the solvent cement like #A05-0303 or #3447530889 to…

view full answer...

Answer 7

We usually tell people to look for about 3 inches of clearance to account for the total travel capabilities of trailer suspension. If you have less than 3 inches you might be able to compensate by using slightly longer shackle straps. I have included…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Would Weight Distribution Hitch Need to be Adjusted When Adding Timbrens to 2021 Toyota Tundra

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching