Empire Faucets RV Kitchen Faucet Supply Line Length.

Question

Question:

What is the length of the supply lines from the bottom of the faucet? My trailer piping is not very flexible.

asked by: Gerald F

1

Helpful Expert Reply:

That is a great question. I looked into this and went out to measure the supply lines.

--Empire Faucets RV Kitchen Faucet - Single Lever Handle - Brushed Nickel # EM54JR.

The cold water line is 4-1/2 inches long and the hot water line is 6-1/4 inches long.

expert reply by: David B

1

Answer 1

Hi Steve, I checked with the manufacturer, and they don't make for sale replacement parts for the Empire Faucets RV Kitchen Faucet #EM54JR. If it's dripping, you can try undoing the water lines and see if there is some type of clog or back-up…

view full answer...

Answer 2

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 3

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 4

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 5

Not just any faucet will work so you'll want to take one quick measurement of your inlet shanks from center to center to make sure that the replacement matches. The #EM65FR you were looking at has an 8" spacing for the inlet shanks. Other…

view full answer...

Answer 6

Hey Phil, so your 2008 Jayco Seneca 36MS has a diesel engine so the correct TruTrac part is the #RM-TRAC45-5500 which is compatible with the front sway bar part #RM-1109-158 and rear bar #RM-1109-157. The front bar and the TruTrac do not attach to…

view full answer...

Answer 7

Hey Jeremy, the Utopia RV Faucet #UT93FR that you referenced requires a hole that is 1-1/2 inch in diameter since it's a single handle design. Usually if the center hole is 1.25 inch it's because there are two other holes on either side for…

view full answer...

Answer 8

Hello Doug, thanks for reaching out. We do carry a replacement handheld shower head, the Camco RV and Marine Handheld Showerhead #CAM43711, but I am sorry to say we do not have one in black. If you must have one in black, we do have the Phoenix…

view full answer...

Answer 9

The seal you need for your trailer hub is the #58846. Or for a bearing kit that includes all of the components you'll need you'd want the #BK2-100. For brake assemblies you'd want the part #AKEBRK-35L for the left side or part #AKEBRK-35R…

view full answer...

Answer 10

The correct replacement motor for your Model 28 Kwikee steps manufactued in 2000 is the part #LC379608. Thank you for including the photo, that always makes things easier. I've linked to a product description video featuring the #LC379608…

view full answer...

Answer 11

Hey Timothy, the EZ Coupler Self Threading RV Sewer hose part #F02-3108 that you referenced basically be used on any RV hose due to it's universal design.

view full answer...

Empire Faucets RV Kitchen Faucet Supply Line Length.

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching