On Part # TSS-107-40 What Is The Minimum Dimension Between Frame and Top Of Spring Plate

Question

Question:

What is the minimum dimension between frame and top of spring plate?

asked by: Steve M

0

Expert Reply:

The # TSS-107-40 will not work on spring plates wider than 4.25 inches. The total height with the spacers is 6.75 inches, and without the spacers is 5.75 inches.

I have attached a review video link below.

expert reply by: Noah E

0

Answer 1

You may be able to reuse the same shackle bolts provided that they are the correct size, are not severely rusted, and are not cracked or otherwise damaged, but not the lock nuts. If you think your bolts might be rusted, cracked, or damaged I would…

view full answer...

Answer 2

Hey Tom, thanks for the picture. So the problem will be that when you hit a bump the spring will run out of room to flatten out so the suspension will essentially get very hard at that point and the trailer will bounce pretty hard. I would recommend…

view full answer...

Answer 3

Yes, you could use leaf springs for a 4,000 lb axle, like part #e57SR (rated for 2,000 lbs each), with a 3,500 lb axle but it will make your ride a bit more stiff. The only times that a leaf spring would become damaged is if it is overloaded or has a…

view full answer...

Answer 4

No, that is not completely true. The wet bolts can be re-used as long as they are not rusted, cracked or damaged in any other way, to include the splines or threads being damaged. The main thing that you'd want to replace is the lock-nut which…

view full answer...

Answer 5

Hey Eric, The hitch extenders that we currently offer for a 2-1/2" receiver tube opening unfortunately max out at 6,000lbs GTW and wouldn't be capable of towing the trailer. You're most likely going to need to upgrade to a TorkLift…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

On Part # TSS-107-40 What Is The Minimum Dimension Between Frame and Top Of Spring Plate

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching