Wrench and Socket Sizes Needed To Tighten Curt 1-7/8" Hitch Ball # C40002

Question

Question:

Product #C40002 What size socket do you need for the nut to attach to the torque wrench? What size of wrench do you need for the ball to hold for torque?

asked by: Michael W

0

Expert Reply:

The 1-7/8" Hitch Ball # C40002 will require a 1-1/2" Socket # ALL643210. You will need a wrench that will open to 1-5/8" to hold the ball in place while torqueing the nut.

expert reply by: Bud M

0

Wrench and Socket Sizes Needed To Tighten Curt 1-7/8" Hitch Ball # C40002
(click to enlarge)

Answer 1

The plug is behind the driver side taillight. You will need to remove several interior panels to access it. To see where the plug is for installing the Curt Wiring Harness part #C55370 check out the video I attached. It's for the Tow Ready…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

I was able to (miraculously) find an online version of the owner's manual for your 1999 Chevrolet Astro and found on page 4-32 that the max trailer weight you can tow is between 4,500 lbs and 5,500 lbs depending on your axle ratio and if you have…

view full answer...

Answer 4

I went out to the warehouse to inspect the hardware included with Reese friction sway control #83660. The hex head self tapping screws will take a 5/8 inch socket.

view full answer...

Answer 5

For the dual friction you are looking for, I recommend adding the Reese Friction Sway Control Kit - Economy - by Draw-Tite, Reese and Hidden Hitch #83660 to your hitch ball. This adjustable friction sway bar can be added using the Reese Sway-Control…

view full answer...

Answer 6

Yes, for friction sway control bars such as #83660, #17200, or any of the similar options the ball size used is the same (1-1/4") so you will be able to use replacement ball and plate #C17201.

view full answer...

Answer 7

The length of the shank on the Replacement Ball for Curt Friction Sway Control System #C36BR is 1-3/4" (see attached).

view full answer...

Answer 8

On a 7 pin round which is the common connection on a semi trailer, the clearance/marker lights are at the 10 o clock position when you look at the trailer wiring connection. When looking at the connector on the back of the truck, that will put the…

view full answer...

Answer 9

I recommend the etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs item #989900 for your 2020 BMW X3. This will give you a couple options for height on where your ball should be. This will fit the 2' receiver in your X3's factory tow…

view full answer...

Answer 10

The Curt hitch ball #C40007 has a 1" diameter shank. Curt Hitch balls with a 1" shank will use a 1-1/2" wrench for the nut. You would also want to use a 2" wrench for the flats on the base of the ball. We offer the 6-point hex…

view full answer...

Answer 11

Yes, the Kenda Karrier S-Trail ST145/R12 Radial Trailer Tire #AM10140 referenced in your question will fit the same 12 inch wheel with a 4 inch width that your existing 4.80-12 size tires are mounted to. Just note that the ST145/R12 tire will be…

view full answer...

Answer 12

I do not recommend running down the highway with your 4.80/4.00-8 trailer tires at 75-80 mph. Most 4.80/4.00-8 trailer tires have a maximum speed rating of 65 mph which will need to be adhered to unless otherwise stated on the tire with an alphabetic…

view full answer...

Wrench and Socket Sizes Needed To Tighten Curt 1-7/8" Hitch Ball # C40002

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching