Brophy Hitch Balls Made in the USA

Question

Question:

Can you verify where the Brophy hitch balls are made? Looking for a 2inch with a 1inch shank sc23-c made anywhere other than China. Thanks

asked by: Brian E

0

Expert Reply:

The Brophy 2" Hitch Ball - 1" Diameter x 2-1/8" Long Shank - Stainless - 7.5K item # SC23-C you referenced is made in Clackamas, Oregon.

expert reply by: Jerred H

0

Answer 1

Brophy hitch ball #SC23-C is made overseas. For a stainless steel option that is made in the US you would have to go to an interchangeable set, #903B. I have linked a video review of this set for you.

view full answer...

Answer 2

In the USA a tandem axle utility trailer with a gross vehicle weight rating (GVWR) of 7500-lbs should have brakes installed. Any trailer over 3000-lbs must have brakes on all wheels in most states, but laws do vary. Some states require braked axles…

view full answer...

Answer 3

The 2" Hitch Ball part #EH68C-C is made overseas but we do have a made in the USA hitch ball option for you, the Convert-A-Ball Interchangeable Ball Set part #904B which gives you both 2" and 2-5/16" options. The majority of the…

view full answer...

Answer 4

Yes, Buyers Products like the #337B0681 are made in the USA. They do all of their engineering, manufacturing and assembly in the USA. They are based out of Ohio.

view full answer...

Answer 5

Some are, and some aren't. Most of Curt's ball mounts are made in the USA, each individual product description will identify if they were manufactured in the USA. All the Convert-A-Ball ball mounts we offer are manufactured in the USA.…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Brophy Hitch Balls Made in the USA

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching