Replacement Spindle Nut and Tang Washer for Dexter 10k Axle

Question

Question:

looking at an axle/spindle nut and washer for a dexter 10k lb axle, nut that has cotter key that run thru it, cant seem to find them

asked by: Jeff

0

Expert Reply:

Since the Dexter 10k axles have a 1-1/2 inch threaded diameter the correct replacement nuts would be the # 6-96. The tang washer you could use with this would be # 5-59.

expert reply by: Jameson C

0

Answer 1

From what I could find out about the wheels on the Haul-Master trailers, they do utilize a 5.30-12 tire and wheel combo. The Kenda 5.30-12 with 5 on 4 1/2 bolt pattern #AM30740 will definitely fit. That being said, it does have a B weight rating,…

view full answer...

Answer 2

Hey Deven, thanks for reaching out, and good question. For a 12 volt system, the charge controller can handle one 200 watt panel. For 24v systems it can do two 200 watt panels. So while the kit technically is expandable, with your 12v system, the one…

view full answer...

Answer 3

The most common bearings and seals for a 7,000 pound axle are #25580 inner bearing, #14125A outer bearing, #25520 inner race and #14276 outer race. The grease seal can vary, and will usually either be the #GS-2250DL, which has a 2.250 inch inner…

view full answer...

Answer 4

According to the instructions for the Bulldog Velocity Series Electric Landing Gear Jack #BD185400 there are 2 ways to install this jack; you can either use at least four 1/2" grade 5 bolts, or four U-Bolts. There are no adapters to make this…

view full answer...

Answer 5

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Answer 6

Without any identifying information on your trailer jack it's just a guessing game at this point. If you do end up taking your jack apart and it's rated for 10K then you just need to measure the spring to ensure the Replacement Return Spring…

view full answer...

Answer 7

Hey Zachary, What kind of specs are you needing for the Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks #TJD-12000-RSP? It's designed to work with 10k rated etrailer and Ram square jacks. While retracted the spring is…

view full answer...

Answer 8

Hey TJ! The new Furrion Chill Cube item #LC54DX is only compatible with other Furrion Cube components. You would need to purchase the Furrion Chill Cube item #FR69TD in white or item #FR49TD black if you would like to upgrade. A direct replacement…

view full answer...

Answer 9

Last time you contacted us I sent the serial number over to Dexter and they indicated the last digit is in fact a 9. So the serial number is 3653139. I have attached the spec sheet that they sent me. The Dexter 10k axles should have a 1-1/2 inch…

view full answer...

Answer 10

The Dexter Trailer Hub Drum Assembly part #8-430-5UC3 I do show as the correct replacement for the Dexter 9-123 Drum.

view full answer...

Answer 11

EZ Lube spindles are generally preferred over Bearing Buddy setups. The EZ lube allows you to insert grease down the middle of the spindle easily which is basically the best option aside from removing the hub and taking it all apart and cleaning and…

view full answer...

Answer 12

A replacement tang-style spindle washer like part #5-101 is intended to be installed behind the castle nut and have its prongs bent down so that they prevent the castle nut from rotating on an E-Z Lube type spindle. The castle nut holds the washer in…

view full answer...

Replacement Spindle Nut and Tang Washer for Dexter 10k Axle

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching