Left and Right Handed Dutton-Lainson Winches

Question

Question:

is there a right and left handed version? or can I change sides. My project requires RH and LH winches. Ive done it with harbor freight winches, but they are cheap and rust up quickly. thanks

asked by: Scott M

0

Expert Reply:

I have a potential solution for you but the Dutton-Lainson Hand Winch DL15504 is just a right hand version and can not be changed to left handed. Dutton-Lainson does make a few left handed winches that we carry.

Left Handed Winches:
The Dutton-Lainson Hand Winch # DL74FR is an 800 lb. winch

The Dutton-Lainson Hand Winch # DL16331 is an 1,200 lb. winch

The Dutton-Lainson Hand Winch # DL15403 is an 2,500 lb. winch. There is the Dutton-Lainson Hand Winch # DL14825 that is the right handed 2,500 lb. winch if you wanted the winch weights to match.

We also have the Hand Winch Cable with Safety Hook 7/32" Diameter x 50' Long # DL24045 which is compatible with the above winches and is rated for up to 2,500 lbs.

expert reply by: Scott S

0

Answer 1

For your Jet Ski Lift, I recommend the Dutton-Lainson Hand Winch w/ Automatic Brake - TUFFPLATE Finish - 1,500 lbs #DL14927 or the 2,500 lbs #DL14958. These winches are designed for use on boat lifts and have the covered gears for safety. They both…

view full answer...

Answer 2

I spoke with my contact at Dutton-Lainson regarding your Hand Winch #DL15303. On this particular unit the handle can in fact be reversed (to be on the left side instead of the right). In order to do this, you will basically need to take apart the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Left and Right Handed Dutton-Lainson Winches

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching