What is Exterior Overall Length of UWS Toolbox part # UWS01047

Question

Question:

I need to know for sure that the length of this box is NO more than 60” including the lid. I have a 2021 Ram 3500 dually, 8’ bed. I also have the Tuxedo deuce ll. Distance between the inside rails is just barely over 66” and the attachment tabs for the deuce are 3”, so if the lid for instance makes the length more or if it is 60 1/2” it won’t work.

asked by: Chuck

0

Expert Reply:

The overall length of the lid of the UWS toolbox part # UWS01047 is exactly 60 inches like you are wanting it to be.

expert reply by: Jameson C

0

Answer 1

Both the UWS Truck Bed Chest - Wedge Series part #UWS01047 and #UWS01032 are considered wedge designs because they are both shaped to maintain capacity and avoid the wheel wells of the truck. The wedge is referring to the wedged sides of the box and…

view full answer...

Answer 2

The overall height of the UWS Truck Bed Chest #UWS01047 is 17-1/4 inches which is going to be shorter than the height of your truck bedrails so it will pretty easily fit underneath your tonneau cover. Now without knowing the length of your bed and…

view full answer...

Answer 3

The UWS Truck Bed Chest #UWS01047 doesn't come with any mounting hardware and doesn't actually have any holes predrilled into it for mounting so it would be a custom job to mount it. That being said you could just drill through the bottom of…

view full answer...

Answer 4

60 inches is the length of the box including the lip around the lid of the DeeZee #DZ8560WB that you referenced. The lower portion is exactly 59-1/2 inches wide.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Hey Jerry, GM moved the placement of their puck systems starting with 2020 models so you are correct that the pucks would have the hitch not sit directly over the axle. GM did the math and made sure that this placement wouldn't adversely affect…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

What is Exterior Overall Length of UWS Toolbox part # UWS01047

Product Page this Question was Asked From

Continue Researching