Gap Measurement On the C-Channel for Enclosed Trailer # 362212-955

Question

Question:

Hi I was looking at your 1inch c channel aluminum trim, it says its 1 tall and 1 deep, which sides are you classifying as the tall and which side is the deep? I guess my question is how wide is the channel itself? I have a 1inch piece of foam insulation and a inch piece of hdpe plastic that I would want to put the channel over to trim

asked by: Kyle J

0

Expert Reply:

The channel itself on the C-Channel for Enclosed Trailer # 362212-955 is going to be 1" across the gap. I have attached a picture of this measurement.

expert reply by: Scott S

0

Gap Measurment
(click to enlarge)

Answer 1

We only have the C-Channel or "U-Channel" in the plain aluminum. We do not have it in black and unfortunately I am not sure where to direct you to find it in black. - C-Channel for Enclosed Trailer #362213-955 (Serrated) - C-Channel for…

view full answer...

Answer 2

The Ark stabilizers won't affect your ground clearance, but to determine the right ones that really depends on how high up your frame is off the ground. Overall, the Ark RV Stabilizer Jacks #ARK34FR are 16.6" collapsed and 23.6"…

view full answer...

Answer 3

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 4

I am afraid we do not offer any kind of T-Channel. We have a C-Channel #362213-955, H-Channel #36281-955, J-Channel #362416-955 and even a Z-rail #362417-955. Unfortunately we do not offer anything with a T shape.

view full answer...

Answer 5

When replacing a grease seal, the metal part of the seal will face towards the inside of the trailer and the rubber part of the seal will face toward the back side of the wheel. The air side of the seal is the flat side of the seal and faces out when…

view full answer...

Answer 6

Sounds like your brake controller will apply your trailer brakes if you apply the manual override lever but not when you press the brake pedal. This is a fairly common problem and the solution is the red wire of the brake controller. Make sure it is…

view full answer...

Answer 7

I checked with Dexter and here is the information on tightening the spindle nut on your 8K axle: 1. After placing the hub, bearings, washers, and spindle nut back on the axle spindle in reverse order as detailed in the previous section on hub…

view full answer...

Answer 8

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 9

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Answer 10

We do not carry the spring only for torsion springs on trailer doors. But we do carry the replacement assembly. I have included a link to the options for you to the right. Springs #RS16933LH or #RS16933RH would not work since they are designed for…

view full answer...

Answer 11

To add a gooseneck hitch to your 2024 GMC Sierra 2500 with a 6-3/4' bed, I recommend the B&W Custom Underbed Installation Kit item #BWGNRK1020. It has a massive 30,000 lbs capacity and fits both the 6-3/4' and 8' bed lengths. The…

view full answer...

Gap Measurement On the C-Channel for Enclosed Trailer # 362212-955

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching