Is # LC182851 the Correct Bevel Gear Set for a Happijac 4150 Model?

Question

Question:

Is LC182851 the correct gear set for a Happijac 4150?

asked by: Shirley K

0

Expert Reply:

Yes, the Replacement Bevel Gears for HappiJac Truck Camper Jack Systems # LC182851 is confirmed to fit your Happijac model 4150.

expert reply by: Bob C

0

Answer 1

The Replacement Bevel Gears for HappiJac Truck Camper Jack Systems #LC182851 will work for the 4600 series HappiJac's. The only difference between the 4500 (these work with the 4500) and 4600 series is that the 4600 series has the drop leg…

view full answer...

Answer 2

I do have an option for you but we don't have rebuild kits for the HappiJac Electric Truck Camper Jacks Model 4100 and 4500. These jacks have been discontinued and I recommend a full replacement system, the HappiJac Electric Truck Camper Jack…

view full answer...

Answer 3

I reached out to my contact at Lippert and was able to verify that the Replacement Bevel Gears #LC182851 you referenced are confirmed to work on your HappiJac 4500 model system. This kit will work perfectly as a replacement.

view full answer...

Answer 4

The replacement motor kits that you are seeing will not work with the 4800 series jacks. The 4800 series, uses the 182522 motors and we do not carry them. The 4800 series was discontinued, making it more difficult to find replacement parts. With the…

view full answer...

Answer 5

The replacement manual jack for the 4200 and 4160 jacks are the HappiJac Manual Truck Camper Jack System, part #LC736514-4. We have the electric upgrade kit for this part, so we have the upgrade for you. Because your camper is already pre-wired, you…

view full answer...

Answer 6

The clicking you described hearing on your Happijack 4150 System along with the fact that they aren't raising or lowering the camper might actually be the result of a weak power source. I first recommend simply checking to make sure that the…

view full answer...

Answer 7

It looks like the HappiJac 4100 series jacks had 34.5" of travel, and there are some parts available to replace things in a pinch, but with newer trucks getting taller it might be wise to upgrade to a whole new set of jacks. I recommend taking a…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Is # LC182851 the Correct Bevel Gear Set for a Happijac 4150 Model?

Product Page this Question was Asked From

Continue Researching