Replacing Fulton XLT 1401 Winch With New Upgraded Boat Winch

Question

Question:

I need front cover listed as #16 part F0185204-03 and Right Side shown as 14 on diagram and Left Side shown as 15 on diagram. I need the part numbers for right and left side, along with cost for all three. Please direct me on how and where I need to go purchase items as described above. Respectively

asked by: Robert G

1

Helpful Expert Reply:

The parts you need for your older Fulton XLT1401 are no longer available so you will want to replace your winch. While I'm sure this isn't what you were wanting to hear, I will give you a great replacement option to consider. Fulton F2 Fully Enclosed Trailer Winch with Adjustable Handle - 2,000 lbs # FW20000301 is a very popular upgrade which is rated for 2,000lbs. This winch allows the cable to retract slowly, instead of free-spooling like some other winches on the market. I attached a demonstration video for you.

expert reply by: Andrew N

1

Answer 1

I wish we did but we do not as Fulton basically went out of business.

view full answer...

Answer 2

In order to replace the Fulton XLT1401 Trailer Winch I recommend using the Fulton F2 Fully Enclosed Trailer Winch part #FW20000301 which will actually be an upgrade for you. The added weight capacity is going to put less stress on the winch which in…

view full answer...

Answer 3

You will need a new Winch #F99CR as your current Fulton XLT1401 is obsolete and the parts for it have been discontinued. This Winch #F99CR is rated slightly higher at 1,500lbs and comes with a 20' strap.

view full answer...

Answer 4

You can use the LED Light Bulb Load-Resistor Kit #DI34ZR on that camera power wire to draw the full 12V needed or you can use the Trailer Connector Adapter w/ Lamp-Out Sensor Bypass #20142 that has an integrated load-resistor for that function.

view full answer...

Answer 5

To replace your old Fulton XLT1401 Trailer Winch I recommend using the Fulton F2 Fully Enclosed Trailer Winch part #FW20000301. This winch has a bit higher weight capacity than the XLT1401, so it's going to put less stress on the winch and make…

view full answer...

Answer 6

Yes, the replacement Fan-Tastic Vent Lid part #FVK1020-19 does fit the Fan-Tastic FV1200.

view full answer...

Answer 7

I reached out to my contact at Fulton and the part you are looking for has been discontinued. You will need to replace the entire winch because that ratchet pawl is no longer available and he said no other kit will work. I recommend the Fulton F2…

view full answer...

Answer 8

The Replacement Spring #4769-28 that you referenced will install onto the pawl assembly of your winch. Check out the pictures I attached that show an exploded diagram to see how it installs.

view full answer...

Answer 9

One end of replacement spring #4769-28 goes through the smaller hole on the switch. The other end goes through a small hole on the winch housing itself. The spring will need to be oriented correctly to be installed. I have included a diagram that…

view full answer...

Answer 10

It sure will! The Fulton XLT 1401 winch currently on your bolt trailer uses the industry standard bolt spacing, which the Fulton F2 Fully Enclosed Trailer Winch with Adjustable Handle - 2,000 lbs #FW20000301 also uses. This is 2-1/4" center to…

view full answer...

Answer 11

Thanks for the picture! We sure do! You will want the Replacement Motor for Stromberg Carlson Electric Landing Gear item #LG-142178.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacing Fulton XLT 1401 Winch With New Upgraded Boat Winch

Featured Help Information

Miscellaneous Media

Continue Researching