Do You Have Replacement Parts For a Fulton XLT1401 Winch?

Question

Question:

i need parts for a fulton xlt 1401 winch ratchet pawl spring ii also need a washer i seen a diagram it was number 2 on there

asked by: Robert

0

Expert Reply:

You will need a new Winch # F99CR as your current Fulton XLT1401 is obsolete and the parts for it have been discontinued. This Winch # F99CR is rated slightly higher at 1,500lbs and comes with a 20' strap.

expert reply by: Bud M

0

Answer 1

I reached out to my contact at Fulton and the part you are looking for has been discontinued. You will need to replace the entire winch because that ratchet pawl is no longer available and he said no other kit will work. I recommend the Fulton F2…

view full answer...

Answer 2

To replace your old Fulton XLT1401 Trailer Winch I recommend using the Fulton F2 Fully Enclosed Trailer Winch part #FW20000301. This winch has a bit higher weight capacity than the XLT1401, so it's going to put less stress on the winch and make…

view full answer...

Answer 3

The standard ratio we use for selecting a boat trailer winch is 2:1 which means the winch at a minimum needs to be rated for half the weigh of the boat. The Fulton 2-Speed Trailer Winch part #F142425 is a great option with enclosed housing and…

view full answer...

Answer 4

The Peterson Trailer Tail Light #421KRUS is a sealed waterproof unit, but the bulb will technically replaceable. However, removing the cover to gain access to the bulb will damage this seal and the light will no longer be waterproof, so I do advise…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Do You Have Replacement Parts For a Fulton XLT1401 Winch?

Continue Researching