Is It Normal For The L-Brackets On The Blue Ox TrackPro Weight Distribution System To Angle Back?
Updated 08/05/2021 | Published 08/03/2021
Question:
Hi, I was wondering if its normal on the blue ox track pro following a tow, the l bracket assembly is angled back towards the rear of the trailer. I tap them forward when hitching up. Thank you in advance.
asked by: Pete R
Expert Reply:
It is normal for those brackets to tilt some due to the bracket spacing with different size frames on the Blue Ox TrackPro Weight Distribution # BLU77FR. I spoke to Blue Ox as to if they recommend filling that gap to limit the amount of angle and they assured me that it is not necessary and the system will preform just as well with the angle as if it were perfectly flat.
I would recommend verifying that the bolts are all at their recommended torque settings, which you can find in the installation instructions that I have linked below.
Product Page this Question was Asked From
Blue Ox TrackPro Weight Distribution w/ Sway Control - 7-Hole Shank - 10K GTW, 1K TW
- Weight Distribution Hitch
- WD With Sway Control
- Trunnion Bar
- Fits 3 Inch Frame
- Fits 4 Inch Frame
- Fits 5 Inch Frame
- Fits 6 Inch Frame
- Includes Shank
- 2-5/16 Inch Ball
- Fits 2 Inch Hitch
- Allows Backing Up
- 900 lbs
- Blue Ox
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Search Results: weight distribution hitch
- Shop: Replacement L-Bracket Plates for Blue Ox TrackPro and 2-Point Weight Distribution - Qty 2
- Shop: Flex Power 3,300-Watt Portable Inverter Generator - Gas - Manual Start - 30 Amp RV & 120V GFCIs
- Search Results: weight distribution hitch accessories and parts
- Search Results: l brackets
- Search Results: accessories and parts
- Search Results: blue ox weight distribution hitch
- Shop: Replacement Spring Bar Retaining L-Pins for Blue Ox TrackPro and 2-Point Weight Distribution - Qty 2
- Q&A: Is it Normal For The L-Brackets On Blue Ox Track Pro Weight Distribution Hitch To Pitch Forward?
- Shop: Lippert Electric Trailer Brake Assembly - 10" - Left Hand - 4,400 lbs
- Shop: MORryde X-Factor Crossmember for Standard Frame Hangers
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 6 on 5-1/2 - Pre-Greased
- Q&A: Looking For Replacement Hub For RVD-H-65535 On A Lippert 4,400 lb Axle
- Shop: Blue Ox Base Plate Kit - Removable Arms
- Shop: Base Plate for Tow Bar
- Q&A: What Brand of Bearings Does etrailer hub part # AKHD-655-35-K Use
- Q&A: Replacement Hub and Drum Assembly for Lippert 4,400 lb Axle
- Q&A: Recommended Trailer Hubs and Brakes for Lippert 4,400 Pound Axle
- Q&A: Recommended Replacement Pre-Greased Hubs for a Lippert 4,400 lb Axle
- Q&A: Looking for a Cover for the Lippert Components Power Tongue Jack # LC285318
- Article: Trailer Wiring Diagrams
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Search Results: trailer tires and wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
on Weight Distribution Hitch
