Kodiak Stainless Steel Brake Pad Replacement for Kodiak 10 inch Disc Brake Setup
Updated 08/02/2021 | Published 07/31/2021
Products Featured in This Question
Question:
I purchased the Kodiak Disc Brake Conversion kit for my boat trailer several years ago from etrailer. My brake pads need to be replaced as the pad has come off the backing. I have the 10inch rotors and the trailer is used in salt water so I am thinking the stainless backing would be best. Can you recommend which pads I should purchase?
asked by: Rick R
Expert Reply:
For your 10 inch Kodiak disc brake setup that's going to see saltwater the best option would be the stainless steel replacements part # K225CPSS which are a confirmed fit. These are ceramic too which means minimal brake dust and they also come with a limited lifetime warranty.
Product Page this Question was Asked From
Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Disc Brakes
- LH
- RH
- 3500 lbs
- Brake Assembly
- 5 on 4-1/2
- Hub and Rotor Assembly
- Kodiak
more information >
Continue Researching
- Shop: Kodiak Disc Brake Kit - 10" Rotor - 5 on 4-1/2 - Stainless Steel - 3,500 lbs
- Search Results: kodiak 225
- Search Results: kodiak 225 brake caliper
- Shop: Kodiak Disc Brake Caliper - Stainless Steel - 3,500 lbs to 6,000 lbs
- Shop: Kodiak Ceramic Brake Pads w/Stainless Steel Backing Plate - 3,500 lbs to 6,000 lbs
- Q&A: How to Remove Brake Caliper Pistons to Rebuild Kodiak Disc Trailer Brake Calipers
- Video: All About the Kodiak Ceramic Brake Pads
- Video: The Low-Down on the Kodiak Disc Brake Kit
- Video: Complete Breakdown of the Kodiak Ceramic Brake Pads w/Stainless Steel Backing Plate
- Search Results: kodiak 10 disc
- Search Results: kodiak 225 ss
- Search Results: galvanized trailer hub
- Shop: DeeMaxx Trailer Idler Hub for 3,500-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: Kodiak Ceramic Brake Pads - Stainless Steel Back - 7,000 lbs to 8,000 lbs
- Q&A: Replacement Brake Setup for Trailer with DB-42 Disc Brakes
- Q&A: What is the Difference Between the Kodiak Disk Brake Kits K2R35DKG and K2R35DS?
- Q&A: How to Pick Out Replacement Hubs for a Boat Trailer
- Q&A: Recommended Parts To Convert Drum To Disc Brakes On EZLoader Trailer With 3,500 Lb Axle
- Q&A: What Inner and Outer Bearings Does 3,500 lb Axle Disc Brake Kit Use
- Q&A: Kodiac Disc Brake Kit Compatibility with UFP DB-42 Axle
- Article: Is It Illegal to Leave My Hitch on My Truck?
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: How to Bleed Your Trailer Surge Brakes
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: How to Tell the Weight Rating of a Trailer Axle