Matching Brake Assemblies and Mounting Bolt Pattern of 10 x 2-1/4 Inch Trailer Brake

Question

Question:

I want to make sure I am getting matching Left and Right brakes. AKEBRK-35R-SA and AKEBRK-35L-SA It seems interesting because they are different prices. Also that web page didnt say how far apart the bolts are. I am guessing that it is kind of standard? about 2/3/4?

asked by: Chuck B

1

Helpful Expert Reply:

The # AKEBRK-35L-SA would be the left brake assembly and # AKEBRK-35R-SA would be the right side matching self-adjusting brake assemblies compatible with the 10 x 2-1/4 inch brake drums used on a typical 3500 lb axle. The price we charge for them is based on what our vendors charge us and what the others in the market are asking.

The mounting studs on the brake backing plate measure 2-7/8 inches apart, center to center.

expert reply by: Mike L

1

Mounting Stud Spacing of 3500 lb 10 x 2-1/4 Inch Brake Assembly
(click to enlarge)

Mounting Stud Spacing of 3500 lb 10 x 2-1/4 Inch Electric Trailer Brake Assembly
(click to enlarge)

Answer 1

The American CS6000XL that you referenced is no longer available and there isn't a direct replacement for it but the closest solution as a replacement would be the Progressive Dynamics RV Control Center part #PD4560K18LS8 which as the same…

view full answer...

Answer 2

The best replacement for your CS-6000XL is the Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger #PD4560K18LS8. This has the same 60 amp output and fits a 13-1/4" tall x 10-1/8" long rear cutout. It…

view full answer...

Answer 3

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 4

Yes, the number you listed is a Kwikee 28 Series step like the part #LC3747452 so this would be what you need.

view full answer...

Answer 5

According to our friends at Lippert their Electric Tongue Jack #LC285318 is a sealed unit that wouldn't require adding grease, therefore they didn't include a grease zerk which explains why you are unable to locate one. I will be sending you…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Matching Brake Assemblies and Mounting Bolt Pattern of 10 x 2-1/4 Inch Trailer Brake

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching