Solution for Needing Replacement Master Cylinder for Atwood Actuator

Question

Question:

Hello, Im trying to identify the correct master cylinder for my boat trailer. I have a 1995 Shorlandr trailer with an Atwood 61101. Can you help point me in the right direction for the correct part?

asked by: Tony

0

Expert Reply:

As Atwood is no longer in production, finding replacements can be a bit of a pain which means there isn't a replacement master cylinder available for your coupler.

That being said, the Dexter DX7.5 Drop-N-Go Brake Actuator # 099-175-20 will be a good replacement for your Atwood 61101. This will handle disc brakes and has a 7,500 pound capacity.

expert reply by: Jameson C

0

Answer 1

Hey Shane, so the Timken bearing kits are made in the USA so what would be perfect for you would be the part #TMK52VR is a USA made 3,500 lb axle trailer bearing kit. Have you had bearing problems in past?

view full answer...

Answer 2

We definitely have some trailer jacks you can use as a replacement for your Dutton-Lainson but it doesn't look like anything we have will work as a direct replacement. If you'd like to stick with the Dutton-Lainson brand then I recommend…

view full answer...

Answer 3

Yes, the Fulton Bolt-Thru Swivel Marine Jack #F1411300301 has a matching 3" x 3" bolt pattern to match up to your welded on mounting bracket.

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Solution for Needing Replacement Master Cylinder for Atwood Actuator

Product Page this Question was Asked From

Continue Researching