Does Thule Shim # TH56JV Fit Thule Hullavator TH898

Question

Question:

Im trying to install shims on my Thule 898 Hullavatet I do not know how to place them

asked by: Gail P

0

Expert Reply:

The shims you referenced are actually for the older version of the Thule Hullavator but for your # TH898 the shims part # TH56JV are not for your version and aren't needed actually.

expert reply by: Jameson C

0

Answer 1

Hey Melissa. The Replacement T-Track Bracket #TH24BH is the channel adapter for the current version of the Hullavator item #TH898. To attach your older version of the Thule Hullavator 897XT to the top channel of aero bars you'll need 4 each of…

view full answer...

Answer 2

The brackets on the Thule Hullavator 897 and the Thule Hullavator 897XT are not the same. The first generation Hullavator was designed to only work with Thule square bars, so it will not work with your Thule WingBar Evo. The updated model, 897XT, was…

view full answer...

Answer 3

For you older version of the Thule Hullavator 897XT the only way to attach it to the top channel of aero bars is with the part #TH56JV. The #TH24BH is the channel adapter for the current version of the Hullavator part #TH898.

view full answer...

Answer 4

For the Thule Hullavator part #TH898 the hardware that goes through the part #TH57BH is #853-5439, #TH93BW and #951061254.

view full answer...

Answer 5

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 6

The discontinued Thule AeroBlade Edge uses Thule's AeroBlade Edge technology which mount flush to your 2014 BMW X3 factory side rails so do not extend farther than your side rails. Thule WingBar Roof Rack with #TH711200 is an aftermarket style…

view full answer...

Answer 7

Yes, the Thule Hullavator Pro Kayak Carrier part #TH898 will work with the Thule WingBar Evo Crossbars. These are just an updated version of the Thule AeroBlade Crossbars. The Hullavator can be attached to the WingBar in one of two ways, with…

view full answer...

Answer 8

Hey Nora, so the correct replacement square nut for a Thule Hullavator part #TH898 is the part #853-7557 so that would be what you would want.

view full answer...

Answer 9

To get replacement T-Slot hardware for your older model 897XT Thule Hullavator carriers you need the following parts (4 per Hullavator system): - Square Nut #853-7557 - M6 x 30 Socket Head Cap Screw #TH919063054 - M6 Washer #951061254 I've…

view full answer...

Answer 10

You will actually just use the square nuts that come with the Thule Hullavator Pro #TH898 to mount it on your Yakima JetStream bars (see attached photo). I have attached the installation instructions for you to reference for the installation as…

view full answer...

Answer 11

If you need the smaller top cradle then you can go with Replacement Cradle Assembly for Thule Kayak Carrier - Top #7521771001. If you happen to also need the larger bottom cradle then the correct part is Replacement Cradle Assembly for Thule…

view full answer...

Answer 12

Hi Leon, Factory roof racks typically have a low weight capacity and won't have enough overhang for a kayak carrier with lift assist to be compatible so I definitely recommend checking the capacity and overhang to see if you can use it. The Thule…

view full answer...

Does Thule Shim # TH56JV Fit Thule Hullavator TH898

Products Featured in This Question

Continue Researching