Replacement Hitch Bolt for Thule Hitching Post Pro

Question

Question:

Does this work for the TH934XTR bike rack? If not can you send me a link to the bolt for the hitch for that bike rack? Thank you.

asked by: Nicole P

0

Expert Reply:

I spoke with our contact at Thule and she confirmed that part # 908-1240-54 is the correct replacement bolt for the Thule Hitching Post Pro Bike Rack, part # TH934XTR.

If you also need a replacement washer and lock washer for the bolt, you can use parts # 956122159 and # 951-1224-54.

expert reply by: Jameson C

0

Answer 1

To replace the threaded hitch pin bolt for your Thule Pro 934 bike rack you need part #TH62RE. We also have the replacement hardware kit #7520990001 if you need more than just the hitch bolt, or part #THSTL2 if you want the locking hitch pin kit.

view full answer...

Answer 2

I am sorry to hear about the issue you are having while using your bike rack. I do have some options for you to display your license plate with the bike rack attached but Thule does not offer any products for this purpose. The vast majority of law…

view full answer...

Answer 3

The Replacement 12 x 40 mm Hitch Bolt for Thule Hitch Bike Racks and Goalpost Hitch Mounted Load Bar #908-1240-54 threads into a welded nut inside the hitch bar for your Thule accessory. There is not a specific nut that fits this bolt. If you can…

view full answer...

Answer 4

I checked with my contact at Thule and verified that the Thule replacement hitch bolt you are looking for is part #908-1240-54. It is a 12 x 40mm hex bolt with a property class of 8.8. It should be installed with M12 washer, #951-1224-54, and M12…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Replacement Hitch Bolt for Thule Hitching Post Pro

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching