Which Fuse For Trailer Running Lights On 2010 Ford F-150

Question

Question:

My Ford 2010 f-150 Pulling my boat. My brake lights blinkers work great. My lights don’t This is not a problem in boat. What fuse runs the lifhts

asked by: Chuck

0

Expert Reply:

Since the running lights on your boat trailer are not working when plugged in to your 2010 Ford F-150, but you know the issue is on the truck then I recommend checking Fuse 31 in the engine bay fuse box. This is a 20 amp fuse so if it is missing or blown you will need to replace it with another 20 amp fuse.

expert reply by: Samuel C

0

Travis

8/31/2024

You the man! Sam

Answer 1

There is one fuse location and two relay locations you will want to check in the power distribution box in the engine compartment. First, check the 20-amp fuse in location 45. This is the Trailer tow stop turn relay feed. If that checks out fine,…

view full answer...

Answer 2

Since the trailer connector on your 2013 Ford F-150 is no longer sending power to the turn signal circuits on your trailer you will need to replace fuse #73. This 20-amp fuse is located in the engine bay fuse box and is what sends power to the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hey Robert, congrats on your new 5th wheel trailer! It is highly recommended to use a sliding hitch like the B&W Companion item #BWRVK3370 the shorter 6-3/4' bed on your 2026 Ford F-350. The slider will ensure you have clearance when making…

view full answer...

Which Fuse For Trailer Running Lights On 2010 Ford F-150

Continue Researching