How Long are the Mounting Screws for the Low Profile LED Flood Light?

Question

Question:

HOW LONG ARE THE MOUNTING SCREWS FOR THIS LIGHT ?

asked by: JACK B

0

Expert Reply:

The Low Profile LED Flood Light # OPT64FR does not come with mounting hardware. However, the holes are about 5/16 of an inch in diameter and the distance between the mounting holes are 3-3/4 inches apart. I went ahead and linked a video to some more measurements of the flood light. To purchase the screws, I recommend buying them from a local hardware store.

expert reply by: Bob C

0

Answer 1

The Low Profile LED Flood Light #OPT64FR is rated IP X7. This means the device has level 7 water sealing, while its protection against dust is unknown.

view full answer...

Answer 2

Yes, since the Low Profile LED Flood Light #OPT64FR puts out 1,000 lumens it would easily light up a door/ramp like you mentioned.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

How Long are the Mounting Screws for the Low Profile LED Flood Light?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching