Which MaxxFan Circuit for MaxxFan with Electric Lift Arms and Rain Sensor

Question

Question:

is there a vidio that shows how to replace a Maxxfan Roof Vent Circuit Broad Do Not Know Model # Fan has a Rain Senor and two lift arms and a wall mount control.

asked by: Gary

0

Expert Reply:

Since your MaxxFan has powered lift arms and a rain sensor that would mean you have the # MA00-04751KSX and the required circuit board replacement is the part # MA39FR.

At this time we do not have an install video we can share though.

expert reply by: Jameson C

0

Answer 1

Hi Stephen; to install the MaxxFan Deluxe Roof Vent w/ 12V Fan, Thermostat, and Remote #MA00-07500K you will need to completely remove your old MaxxFan Plus. Even if the parts carried over, I would recommend complete replacement since that plastic…

view full answer...

Answer 2

The correct replacement circuit board for the MaxxFan Deluxe Roof Vent 7500K is the Replacement Printed Circuit Board for MaxxAir Powered Lift RV Roof Vents part #MA10A21275K.

view full answer...

Answer 3

I did some checking and for the MaxxAir the correct replacement circuit board is the #MA39FR.

view full answer...

Answer 4

If you have the wall control part #MA00A03550K installed in the wall of your trailer the Maxxair Fan part #MA00-04751KSX would easily integrate into it and work great. If you have a different switch setup let me know and I'll see what options you…

view full answer...

Answer 5

Most likely it's the circuit board since it's the part that activates the motor. The circuit boards are model specific so you will need to purchase the correct board for your model. This means you will have to look at your fan to find the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Which MaxxFan Circuit for MaxxFan with Electric Lift Arms and Rain Sensor

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching